Hardinge SERIES I Installation Operation & Maintenance Download Page 6

Page: 6 / 23

FEED CONTROL LEVER

Feed Control Lever “I”, Figure 2.8, engages

overload clutch on pinion shaft when positioned left
and will stay engaged until either quill stop comes in
contact with micrometer adjusting nut, forcing feed
control lever to drop out automatically, or release
manually by engaging lever to right.

FEED CONTROL OVERLOAD CLUTCH

The Feed Control Overload Clutch is set at the

factory to hold up to 200 lbs of down pressure on
quill, which will accommodate drills up to .375”
diameter in mild tool steel.

- CAUTION -

This clutch should not be tampered
with in the field.

- NOTE -

The feed control lever must be en-
gaged in order to use manual feed
controls. the quill feed handle and
manual

feed

handwheel

may

removed when not in use.

QUILL

Quill “J”, Figure 2.9, contains the spindle

assembly and can be raised or lowered by using the
quill feed handle “M”, Figure 2.10.

SPINDLE

Spindle “K”, Figure 2.9, performs the actual

rotation and also retains the machine tooling.

QUILL LOCK

Quill Lock “L”, Figure 2.9, is a friction lock for use

when quill is in a stationary position such as a milling
operation. It is recommended that this lock be used
whenever quill movement is not desired.

M-450

2-5

Figure 2.8 - Feed Control Lever and

Feed Control Overload Clutch

Engage

Disengage

TP5292

Figure 2.9 - Quill, Spindle and

Quill Lock

TP5293

Summary of Contents for SERIES I
























Search results

Summary of Contents for SERIES I

Reviews:

Related manuals for SERIES I

Brands by name

Popular brands

Hardinge SERIES I, Installation Operation & Maintenance

Search results

Summary of Contents for SERIES I

Reviews:

Related manuals for SERIES I

Brands by name

Popular brands