background image

SKU 94903     For technical questions please call 1-800-444-3353 

Page 5  

operATion

igniting and extinguishing The Torch:

To ignite the torch push the Gas “On/Off” Switch forward towards the tip until the 
Gas “On” Lock button pops out. This will lock the Gas “On/Off” switch in the “On” 
position. 

Next push the “Piezo Igniter” button forward repeatedly until the torch is lit.

To turn off the torch, push the Gas “On” Lock button. By doing this the Gas “On/Off “ 
switch will slide to the off position and extinguish the flame. If the flame continues to 
burn, press the “Flame Off Button”.

Allow the tool to cool down before setting it down. Only set the tool down after the 
stand has been opened. See page 7 for instructions regarding this.

      

WARNING:

  never leave the tool unattended while in operation or while hot. Serious 

personal injury and risk of fire may result.

Setting up the Soldering iron:

The Torch comes with the “Soldering Iron Adapter” already installed. It is the longer 

of the two adapters and has a threaded end that receives the soldering tips. 

If you do need to install “Soldering Iron Adapter”, first remove the “Adapter Lock 

Nut” then slide the “Soldering Iron Adapter” over the ceramic insulator, then thread 

on the “Adapter Lock Nut”.  

Pick the desired tip from the kit and screw it onto the end of the “Soldering Iron 
Adapter”.

1.

2.
3.

4.

1.

2.

3.

Soldering Iron Stand

Soldering Iron Adapter

Piezo Igniter

Adapter Lock Nut

Gas “ON” Lock Button

Gas “ON” Lock Switch

REV 07j

Summary of Contents for TORCH KIT 94903









Reviews: