background image

Page 3

For technical questions, please call 1-888-866-5797.

56385 

        

SAF

eT

y

O

Pe

RA

Ti

O

n

M

A

in

Ten

A

n

C

e

Se

Tu

P

WARninG SyMBOLS AnD DeFiniTiOnS

This is the safety alert symbol.  It is used to alert you to potential 

personal injury hazards.  Obey all safety messages that 

follow this symbol to avoid possible injury or death.

Indicates a hazardous situation which, if not avoided,  

will result in death or serious injury.

Indicates a hazardous situation which, if not avoided,  

could result in death or serious injury.

Indicates a hazardous situation which, if not avoided,  

could result in minor or moderate injury.

Addresses practices not related to personal injury.

Symbol

Property or Statement

Wear heavy-duty, cut- and 

abrasion

-

resistant leather gloves.

Wear AnSi-approved safety glasses.

Cut or sever hazard.

Roller entanglement hazard.

Hot surface burn hazard.

Fire hazard.

Caustic chemical (acid) hazard.

explosion hazard.

Do not loop the synthetic rope 

around object and hook onto itself.

Do not place finger(s) through hook.  

Fingers may be caught and get 

pulled into fairlead or drum.

Pull hook using strap only.

Symbol

Property or Statement

Do not use winch in overwind 

orientation. (Synthetic rope 

enters/exits at the top.)
use winch only in 

underwind orientation.  

(Synthetic rope enters/

exits at the bottom.)

VDC

Volts Direct Current

A

Amperes

CCA

Cold Cranking Amperes

HP

Horsepower

fpm

Feet Per Minute

mpm

Meters Per Minute

RPM

Revolutions Per Minute

iP

International Protection rating

Classifies the degrees of protection provided 

against the intrusion of solid objects, 

dust, accidental contact, and water.

G8

Grade 8 

A fastener strength rating.

Summary of Contents for BADLAND APEX 12000





















Reviews: