background image

SKU 99681 

For technical questions, please call 1-800-444-3353. 

Page 8

Front Center Beam With Holes (5) 

using Bolts (27), Washers (22), and 

Nuts (24).
Attach the Center Drawer Mount With 

8. 

Glide Rail (13) to the two “L” Brackets 

(11, 12) using Bolts (27), Washers 

(22), and Nuts (23).

Fig. 6

25

23

Rear Plate of 

Drawer 14R

Front Plate of Drawer 14F

Side Plate of 

Drawer 15

9.  Attach the Front Plate of Drawer 

(14F), Side Plates of Drawer (15), 

and Rear Plate of Drawer (14R) to-

gether with Bolts (25) and Nuts (23).
Repeat for the second drawer. Do not 

10. 

tighten the screws on the “L” Brack-

ets, Center Drawer Mount With Glide 

Rail and two drawers until the two 

drawers are fit into the bench frame.

Fig. 7

27

22

23

Top Shelf Left 

Side Beam 7L

Top Shelf 

Front Beam 4

Top Shelf Right 

Side Beam 7R

Peg Board 17

11.  Attach the Peg Board (17) to the 

bottom holes of the Top Shelf Back 

Beam (3) using Bolts (27), Washers 

(22), and Nuts (23). 
Attach two Top Shelf Side Beams (7L, 

12. 

7R) onto the Left & Right Post Exten-

sions (2L, 2R) with Bolts (26), wash-

ers (22), and Nuts (23)
Attach the Top Shelf Front Beam (4) 

13. 

with Bolts (26), Washers (22), and 

Nuts (23).

Fig 8

18

28

14.  Place the Top Shelf (18), Bench Top 

(19), Drawer Boards (20), and Bottom 

Board (21) into position.  Attach the 

Top Shelf (18) using Wood Screws 

(28).

Summary of Contents for 99681













Reviews: