background image

Page 5

SKU 96695

For technical questions, please call 1-800-444-3353.

Using the Large Carriage Bolts (6), loosely attach the Brace Clamps (5) over the 

corners of the base and top frame.  

please note:

 Be sure to keep the bolt heads 

on the outside of the Clamps (5).
Place a Corner Support Post (3) into each of the Brace Clamps (5) along the bot-

tom frame.  Finger-tighten the Carriage Bolts (6).  Have an assistant keep Posts 

supported until secured.   

 

please note:

 You will have one remaining Support Post (3) to use for the Gate.

With assistance, lift the top frame up and attach the corners to each of the 

Support Posts (3).  Sliding the Brace Clamps (5) along the corners will aide in 

straightening the Kennel frame.  Tighten in place by using four Large Carriage 

Bolts (6).  See 

Figure b

, below. 

 

 

 

 

 

 

 

 

 

 

 

 

 

Tighten all Carriage Bolts (6) with a wrench (not included).
Select a corner Support Post (3) and using a tape measure (not included), mea-

sure 35-1/2” from the Support Post.  Mark the sport where the measurement 

ends.  Attach a Brace Clamp (5) to the marked spot  on the bottom frame.  
Attach the last Support Post (3) to the bottom Brace Clamp (5).  This Support 

Post will be the Gate Support Post.  Secure a Brace Clamp (5) to the marked 

spot on the top frame and connect it to the top of the Gate Support Post. 

 

please note: 

 Make sure the distance between Gate Support Post and corner 

Support Post is 35-1/2” before tightening Clamps with Large Carriage Bolts (6)
Once all the Carriage Bolts have been tightened, untie the Large Chain-Link 

Fencing (1). 

 

caution!

  Avoid sharp ends and tangles while untying the roll.  

4.

5.

6.

7.
8.

9.

10.

Figure b

Brace Clamp (5)

Large Carriage 

Bolts (6)

Top Frame

Tension Bar (4)

Clip (7)

Chain Link Fencing (1)

Summary of Contents for 96695












Reviews: