background image

Page 4

For Pressure Washer technical questions, please call 1-800-444-3353.

SKU 67546/67596 

For engine technical questions, please call 1-800-520-0882.

Set up Precautions

1. 

Gasoline fuel and fumes are flammable, and 

potentially explosive.  Use proper fuel storage 

and handling procedures.  Do not store fuel 

or other flammable materials nearby.

2. 

Have multiple ABC class fire extinguishers nearby.

3. 

Operation of this equipment may create sparks 

that can start fires around dry vegetation.  A spark 

arrestor may be required.  The operator should 

contact local fire agencies for laws or regulations 

relating to fire prevention requirements.   

4. 

Set up and use only on a flat, level, 

well-ventilated surface.

5. 

The work area should have adequate 

drainage to reduce the possibility of 

a fall due to slippery surfaces.

6. 

Wear ANSI-approved safety goggles, 

heavy-duty work gloves, and dust mask/

respirator during set up and use.

7. 

Use only oil and fuel recommended in the 

“Specifications” section of this manual.

8. 

Only use cold Water or pressure washer 

detergent in this tool.  Do not use caustic 

materials, solvents, flammable materials, or 

detergents not designed for pressure washers.  

Use of any such material can cause injury, 

or damage this tool or personal property.

9. 

Do not dry run this product.  Dry running 

will cause serious damage to the seals. 

Make sure the water supply used for the 

Pressure Washer is not dirty or sandy.

10.  Prior to starting the Pressure Washer in 

cold weather, check all of the parts of the 

unit to make sure ice has not formed.  Do 

not store the unit anywhere that the 

temperature will fall below 32° F (0° C).

Operating Precautions

1. 

CaRBOn mOnOxiDe hazaRD 

using an engine indoors Can Kill 

YOu in minuteS. 

Engine exhaust contains carbon 

monoxide.  This is a poison you 

cannot see or smell. 

NEVER use inside a home or garage, EVEN IF 

doors and windows are open. 

Only use OUTSIDE and far away from windows, 

doors, and vents.

2. 

Keep children away from the equipment, 

especially while it is operating.

3. 

Do not leave the equipment unattended 

when it is running.  Turn off the equipment 

(and remove safety keys, if available) 

before leaving the work area.

4. 

Wear ANSI-approved safety goggles 

and hearing protection during use.

5. 

People with pacemakers should consult their 

physician(s) before use.  Electromagnetic 

fields in close proximity to a heart pacemaker 

could cause pacemaker  interference or 

pacemaker failure.  Caution is necessary when 

near the engine’s magneto or recoil starter.

6. 

Use only accessories that are recommended 

by Harbor Freight Tools for your model.  

Accessories that may be suitable for 

one piece of equipment may become 

hazardous when used on another one.

7. 

Do not operate in explosive atmospheres, 

such as in the presence of flammable 

liquids, gases, or dust.  Gasoline-powered 

engines may ignite the dust or fumes.

8. 

Stay alert, watch what you are doing and 

use common sense when operating a 

piece of equipment.  Do not use a piece of 

equipment while tired or under the influence 

of drugs, alcohol or medication.

9. 

Do not overreach.  Keep proper footing and 

balance at all times.  This enables better control 

of the equipment in unexpected situations.

10.  Do not carry the spray handle with your finger on 

the trigger, whether engine is operating or not.

11.  Use this equipment with both hands 

only.  Using equipment with only one hand 

can easily result in loss of control.

12.  Dress properly.  Do not wear loose clothing or 

jewelry.  Keep hair, clothing and gloves away 

from moving parts.  Loose clothes, jewelry or 

long hair can be caught in moving parts.

13.  Parts of the Pressure Washer, especially 

exhaust system components, get very hot 

during use.  Stay clear of hot parts.

Rev 11c

Summary of Contents for 67596





























Reviews: