background image

THANK YOU for choosing a HARBOR FREIGHT TOOLS product.  For future reference, please
complete the owner’s record below:

Model___________

Serial No._____________

Purchase Date_____________

Save This  Manual

You will need the manual for the safety warnings and precautions, assembly instructions, operating
and maintenance procedures, parts list and diagram.  Keep your invoice with this manual.  Write the
invoice number on the inside of the front cover.  Keep the manual and invoice in a safe and dry
place for future reference.

Technical Specifications

Construction:

Cast Aluminum Frame and Steel with welded hinges

Height:

30-3/8"

Table Size:

16" W x 24" Long with 4" clamp travel

Max. Load Capacity: 375 LBS.
The Workbench has 12 dog Holes and 12 Dogs.  It has eight (8) adjustment settings
along with a 23-5/8" Ruler.

Safety Warnings and Precautions

WARNING: When using product, basic safety precautions should always be followed to
reduce the risk of personal injury and damage to equipment.

Read all instructions before using this product!

1.

Keep work area clean.  Cluttered areas invite injuries.

2.

Observe work area conditions.  Do not use this product in damp or wet locations.  Don’t

expose to rain.  Keep work area well lighted.

3.

Store idle equipment.  When not in use, products must be stored in a dry location to inhibit

rust.  Always lock up products and keep out of reach of children.

4.

Use the right product for the job.  There are certain applications for which this product was

designed. It will do the job better and more safely at the rate for which it was intended.  Do not
modify this product and do not use this product for a purpose for which it was not intended.

5.    Check for damaged parts.  Before using any product, any part that appears damaged should

be carefully checked to determine that it will operate properly and perform its intended function.
Check for any broken or damaged parts and any other conditions that may affect its operation.
Replace or repair damaged or worn parts immediately.

6.

Replacement parts and accessories.  When servicing, use only identical replacement parts.

Use of any other parts will void the warranty.

7.

Do not operate product if under the influence of alcohol or drugs.  Read warning labels on

prescriptions to determine if your judgment or reflexes are impaired while taking drugs. If there
is any doubt, do not operate the product.

#47078

                                                                        Page 2

Summary of Contents for 47078








Reviews: