Harbor Freight Tools 42606 Assembly & Operating Instructions Download Page 2

SKU 42606

For technical questions, please call 1-800-444-3353.

Page 2

THANK YOU for choosing a 

HARBOR FREIGHT TOOLS 

product.  For future reference, please complete the

owner’s record below:

Model___________

Serial No._____________

Purchase Date_____________

Save This  Manual

You will need the manual for the safety warnings and precautions, assembly instructions,
operating
and maintenance procedures, parts list and diagram.  Keep your invoice with this manual.
Write the invoice number on the inside of the front cover.  Keep the manual and invoice in a
safe and dry place for future reference.

Technical Specifications

Tool Name:

Metal Work Station

Item Number:

42606

Construction:

Sheet Metal Steel Desk-19 Gauge
Aluminum Drawer Handles
Maple Wood Top

Weight:

105 LBS.

Max. Weight Capacity:

300 LBS. (evenly distributed over Wood Top)

Finish:

Black Enamel-Steel/Varnish/Wood

Overall Dimensions:

54" W x 20-3/16" L x 34-1/2" H

Wood Top Dimensions:

54" W x 20-3/16" L x 1-9/16" T

Desk Dimensions:

42-5/8" x 18" L x 32-7/8" H

Number of Drawers:

5

Inner Drawer Dimensions:

16-7/8" W x  17-3/4" L x 4-1/8" H

Cabinet Dimensions:

22-3/4" W x 18" L x 23-3/4" H

Shelf Dimensions:

22-3/4" W x 18" L x 10-5/8" H (first level)
22-3/4" W x 18" L x 8-3/8" H (second level)

Safety Warnings and Precautions

Read all instructions before using this product!

WARNING: When using tool, basic safety precautions should always be followed to
reduce the risk of personal injury and damage to equipment.

1.    

  Avoid working alone

.  If an accident happens, an assistant can bring help.

2.

Keep work area clean

.  Cluttered areas invite injuries.

3.

Observe work area conditions

.  Keep work area well lighted.

4.

Keep children away

.  Children must never be allowed in the work area.  Do not let them handle machines,

tools, or extension cords.

5.

Store idle equipment

.  When not in use, tools must be stored in a dry location to inhibit rust.  Always lock

up tools and keep out of reach of children.

6.

Use eye and ear protection

.  Always wear ANSI approved impact safety goggles.

Summary of Contents for 42606












Reviews: