background image

19

A

B

C

Printed in China

REPLACEMENT PARTS LIST

For replacement parts, call our customer service department at 

888-251-1003

, 8 a.m. - 8 p.m., EST, 

Monday - Sunday. You could also contact us at [email protected].

JMLI2208

The distributor warrants this fan to be free from defects in workmanship and materials present at time of 
shipment from the factory for Lifetime limited from the date of purchase. This warranty applies only to 
the original purchaser. The distributor agrees to correct any defect at no charge or, at our option, 
replace the ceiling fan with a comparable or superior model.

To obtain warranty service, present a copy of your sales receipt as proof of purchase. All cost of 
removal and reinstallation are the express responsibility of the purchaser. Any damage to the ceiling fan 
by accident, misuse or improper installation, or by using parts not produced by the manufacturer of this 
fan or affixing accessories not produced by the manufacturer of this fan, are the purchaser's own 
responsibility. The distributor assumes no responsibility whatsoever for fan installation during the limited 
lifetime warranty. Any service performed by an unauthorized person will render the warranty invalid.

Due to varying climatic conditions, this warranty does not cover changes in brass finish, rusting, pitting, 
tarnishing, corroding or peeling. Brass finish fans maintain their beauty when protected from varying 
weather conditions. Any glass provided with this fan is not covered by the warranty.

Any replacement of defective parts for the ceiling fan must be reported within the first year from the date 
of purchase. For the balance of the warranty, call our customer service department (

at 

888-251-1003

)

for return authorization and shipping instructions so that we may repair or replace the ceiling fan. Any 
fan or parts returned improperly packaged is/are the sole responsibility of the purchaser. There is no 
further express warranty. The distributor disclaims any and all implied warranties. The duration of any 
implied warranty which cannot be disclaimed is limited to the limited lifetime period as specified in our 
warranty. The distributor shall not be liable for incidental, consequential or special damages arising at or 
in connection with product use or performance except as may otherwise be accorded by law. This 
warranty gives you specific legal rights and you may also have other rights which vary from state to 
state. This warranty supersedes all prior warranties.

LIMITED LIFETIME WARRANTY

J

    PART         DESCRIPTION 

       

A      Downrod

       

B      Canopy

       

C      Mounting Bracket

       J      Blade

   L      Blade Arm

5127846-A
5127846-B
5127846-C
5127846-J
5127846-L

  

PART #      

                   

L

Summary of Contents for TALAMORE TAL60MBK8LR




















Reviews: