background image

6

Lowes.com/harborbreeze

SAFETY INFORMATION

CAUTION:

 Read all instructions and safety information before installing your new fan . Review the 

accompanying assembly diagrams .

CAUTION:

 Be sure the outlet box is properly grounded or that a ground (green or bare) wire is present .

CAUTION:

 Carefully check all screws, bolts, and nuts on the fan motor assembly to ensure that they 

are secured .

CAUTION:

 This equipment has been tested and found to comply with the limits for a Class B digital 

device, pursuant to Part 15 of the FCC Rules . These limits are designed to provide reasonable 

protection  against harmful interference in a residential installation . This equipment generates, 

uses and can radiate radio frequency energy and, if not installed and used in accordance with the 

instructions, may cause harmful interference to radio communications . 

PREPARATION

Before beginning the assembly of this product, ensure that all parts are present . Compare all parts 

with the package contents list and hardware contents list . If any part is missing or damaged, do not 

attempt to assemble the product . 
After opening the top of the carton, remove the mounting hardware package from the foam inserts, 

then remove the motor from the packaging and place it on a soft surface, such as a carpet, to avoid 

damage to the finish.

Estimated Assembly Time:

 120 minutes

Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety 

Glasses, Step Ladder, and Wire Strippers
Helpful Tools (not included): AC Tester Light, Tape Measure, Wiring Handbook, and Wire Cutters

LAMP CONTAINS MERCURY
LA BOMBILLA CONTIENE MERCURIO

Manage in accordance with Spills, Disposal and Site Cleanup 
Requirements.  In case of breakage, follow clean-up 
procedures provided by contacts below.
Manipule según las exigencias sobre derrames, eliminación y 
limpieza del lugar. En caso se rompa, siga el método de 
limpieza proporcionado por los siguientes contactos.

Hg

www.epa.gov/cflcleanup
1-866-284-4010

Summary of Contents for KINGSBURY 40190













































Reviews: