background image

6

Lowes.com/harborbreeze

SAFETY INFORMATION

CAUTION:

 Read all instructions and safety information before installing your new fan. Review the 

accompanying assembly diagrams.

CAUTION:

 Be sure the outlet box is properly grounded or that a ground (green or bare) wire is present.

CAUTION:

 Carefully check all screws, bolts, and nuts on the fan motor assembly to ensure they are 

secured.

PREPARATION

Before beginning the assembly of this product, ensure all parts are present. Compare all parts with 

the package contents list and hardware contents list. If any part is missing or damaged, do not 

attempt to assemble the product.
After opening the top of the carton, remove the mounting hardware package from the foam inserts, 

then remove the motor from the packaging and place it on a soft surface, such as a carpet, to avoid 

damage to the finish.

Estimated Assembly Time:

 120 minutes

Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety 

Glasses, Step Ladder, Wire Strippers and Wire Cutters
Helpful Tools (not included): AC Tester Light, Tape Measure, Wiring Handbook

Summary of Contents for 40945




















Reviews: