V4000 SERIES
OWNER’S MANUAL
13
STEREO MASTER
From the Stereo Master page, choose whether this speaker will act as a
left or right speaker if operating as Stereo Master.
• Turning the Master Volume / DSP knob will determine how audio
will be routed for Smart Stereo operation.
• Pressing the Master Volume / DSP knob will exit this page and
return to the Home Page.
This setting only applies when the 3-position hardware switch is set to
Stereo Master.
•
Is Left:
When this VARI’s physical switch is set to Stereo Master,
it will amplify the left audio via its own power amp and speakers,
and send right audio to the LINK OUT jack so a linked speaker will
amplify right audio.
•
Is Right:
When this VARI’s physical switch is set to Stereo Master,
it will amplify the right audio via its own power amp and speakers,
and send left audio to the LINK OUT jack so a linked speaker will
amplify left audio.
DI FOR STEREO MASTER
To run multiple pairs of VARI speakers as a unified Smart Stereo system,
the DI for Stereo parameter must be set properly.
• Turning the Master Volume/DSP knob will select how the DIRECT
OUT jack will operate.
• Pressing the Master Volume/DSP knob will exit this page and return
to the Home Page.
This setting only applies when the 3-position hardware switch is set to
Stereo Master.
•
Is Mono:
This is the default setting, appropriate for normal use,
including when using VARI speakers individually, or when using a
single pair of VARI speakers in Smart Stereo. With this setting, the
DIRECT OUT provides mono audio output, appropriate for feeding a
separate monitoring system, or an independent subwoofer.
•
Alt-Link:
This setting allows you to operate multiple pairs of VARI
speakers as a unified Smart Stereo system. With this setting, the
DIRECT OUT provides the same audio that the Stereo Master speaker
is amplifying. For example, if the Stereo Master speaker is set to “Is
Left” and “Alt-Link”, it will amplify left audio itself, send left audio to
the DIRECT OUT, and send right audio to the LINK OUT. If the Stereo
Master speaker is set to “Is Right” and “Alt-Link”, it will amplify right
audio itself, send right audio to the DIRECT OUT, and send left audio
to the LINK OUT. See Smart Stereo with Multiple V4112/V4115 Pairs
on page 8 for example use of this setting.
LCD BACKLIGHT DIMMING
From the LCD Backlight page, you can configure the illumination of
VARI’s rear panel display.
• Turning the Master Volume / DSP knob will choose from the
available options.
• Pressing the Master Volume / DSP knob will exit this page and
return to the Home Page.
These options are available:
•
Never:
The display will be lit whenever the VARI is on.
•
30 Seconds:
The display will turn off after 30 seconds of inactivity.
Press or turn the Master Volume, Bass or Treble knobs to light the
display for 30 seconds.
• Turning the Master Volume / DSP knob will choose from the
available options.
• Pressing the Master Volume / DSP knob will exit this page and
return to the Home Page.
These options are available:
•
Off:
LED will not light.
•
Power Only:
LED will light white when power is on.
•
Power+Limit:
LED will light red when the limiter is triggered, and
otherwise will be lit white when the power is on.
The front LED will also light blue during app control.
LED OPTIONS
From the LED Options page, you can configure VARI’s front panel LED.
APP CONTROL ENABLE/DISABLE
From the Enable App Control page, you can enable VARI control for the
VARI 4000 iOS
®
App for iPhone
®
and iPad
®
.
• Turning the Master Volume / DSP knob will enable or disable
app control.
• Pressing the Master Volume / DSP knob will exit this page and
return to the Home Page.
When app control is enabled, the display will show a 4-digit code, as
0000 is shown above. This code is set to 0000 as a factory default,
but can be customized via the app, to prevent others from being able to
control this VARI without the correct app code.
