V3400 SERIES
OWNER’S MANUAL
5
V3412/V3415 BACK PANEL
1
VOICING
Pressing the button selects from the available voicings (tunings) for different
applications:
- Standard: for general use including music playback.
- Club: for boosted bass, good for low volume use with electronic music.
- Speech: for public speaking, may also be helpful for solo performers who are
singing along with acoustic guitar.
- Floor Monitor: for enhanced clarity and reduced feedback potential for floor
monitors, also may be helpful to avoid excessive bass from wall mounted
speakers.
- Club (APP): Download App to customize this VOICING
2
INPUT 1 AND 2 KNOBS
These knobs set the volume for the inputs below them
3
MIC/GUITAR/LINE SWITCHES
Set these to match the type of source connected to the input below them:
- Mic: for microphones, or line level sources with low output volumes.
- Guitar: for acoustic guitar or guitar pedal board.
- Line: for line level sources.
4
INPUT 1 AND 2 INPUT JACKS
Connect XLR or 1/4-inch cables.
5
INPUT 3 KNOB
Sets the volume for all the inputs below, including Bluetooth audio,
Stereo (AUX) Input and line inputs.
6
BLUETOOTH AUDIO INPUT
Press the On/Pair button to enable Bluetooth and initiate pairing mode:
- To pair, look for VARI V3412 or VARI V3415 from your Bluetooth audio
source device.
- LED is lit solid when currently paired, blinking when available for pairing, and off
if Bluetooth has been disabled by a press of the Bluetooth Off button.
- On/Pair button forces any currently connected Bluetooth audio source to
disconnect, and makes the speaker available for pairing.
- Off button disables Bluetooth.
- Bluetooth On/Off state when turning power off will be remembered and restored
when powering on.
7
STEREO (AUX) INPUT
This input accepts stereo or mono unbalanced audio input.
1
2
3
4
5
9
10
11
20
12
18
17
16
15
14
19
13
6
7
8
8
BALANCED LINE INPUTS
Balanced or unbalanced line level sources can be connected here.
9
CLIP LEDS
If a Clip LED lights, turn down that input knob to avoid distorted sound.
10
SUB CUT
Applies a crossover to tune V3412/V3415 for use with a subwoofer.
- Low frequencies are cut from V3412/V3415’s amplifier/speaker.
- MIX OUT jack provides these low frequencies, to feed a subwoofer.
11
PRESET
Press and hold 5 seconds to save current settings. Then press PRESET
briefly any time to recall those settings (physical position of bass and
treble knobs will be overridden by preset values, until/unless you then
turn those knobs).
12
BASS AND TREBLE KNOBS
Adjust the sound of your speaker.
13
ROUTING
- Normal (Mono): This speaker will output mono audio.
- Stereo Master: This speaker will operate as the master speaker of a
Smart Stereo pair. Use a mic cable to connect this speaker’s LINK
OUT to the LINK IN jack of a second speaker of the same type. All
inputs should be connected to the first master speaker, which will also
set the volume and tone of both speakers.
- Link In: Use this setting for the second speaker of a Smart Stereo pair.
The audio from the LINK IN will be routed directly to the power amp
and speaker, with all other inputs and controls being ignored. This
can also be used to accept mono audio from a previous speaker, with
that previous speaker determining volume and tone.
14
MIX OUT JACK
Configured by
13
switch.
15
LINK IN JACK
Activated only when
13
switch is set to LINK IN.
16
LINK OUT JACK
- When ROUTING is set to Smart Stereo, this jack outputs right only
audio to feed a second (right) speaker).
- When ROUTING is set to Normal (Mono), this jack outputs mono
audio to feed a second speaker.
17
CHARGE JACK
Provides power for mobile devices.
18
Connect power cable here.
19
If the speaker will not power on and you suspect its fuse may have
blown, turn off the power switch, and open the fuse compartment using
a small flat blade screwdriver. If metal strip in fuse is broken, replace
with T5 AL 250V fuse (for 100-120 volt use), or T2.5 AL 250V fuse (for
220-240 volt use).
20
Switches the power on and off.
