3
4
Measurement input and range
※ Maximum range of display scale
-1.999 ~ 1.999 / -19.99 ~ 19.99 / -199.9 ~ 199.9 / -1999 ~ 9999
the displaying range of expression changes depending of the set-up location of a decimal point
Input signal
Mode
Input range
Display range Input impedance
Accuracy
AC voltage
5 V ( )
0.1 ~ 9999 Hz
0.1 ~ 9999
100 ㏀
±5 Digit max.
50 V ( )
1 ㏁
500 V ( )
5 ㏁
Comparative output action ( )
Error display code
“ ” : This will be displayed when a measured input value exceeded max display range
(9999 4digits) or when negative valve is indicated with in normal mode. Normal mode : SCH 0 or SCL 0
“ ” : Error message will be displayed when a setting value of High Comparative Output is less than that of
Low Comparative Output
“ ” : When input is less than min measurement range 0.1 ㎐
Parameter composition and setting method
▒ Parameter 1 ( Key - keep pushing the button(min 2 sec))
Key
set up start
Key
set up start
Key
set up start
Key
set up start
Key
set up start
Key
set up start
Key
set up start
Key
set up start
Key
set up start
Key
Key
Key
Key
Key
Key
Key
Key
Key
Key
set up
Key
set up
Key
set up
Key
set up
Key
set up
9.999
1.800 (magnification)
0.500 (magnification)
+99 (Max value error compensation)
0.1
sec
0.2
sec
0.3
sec
0.5
sec
0.8
sec
2.0
sec
2.5
sec
3.0
sec
4.0
sec
5.0
sec
1.0
sec
1.5
sec
-99 (Min value error compensation)
9.999 (Max value of high scale setting)
-1.999 (Min value of high scale setting)
9.999 (Max value of low scale setting)
-1.999 (Min value of low scale setting)
Set the position of decimal point
OFF
H-Hd
OFF
ON
L-Hd
E-Hd
99.99
999.9
9999
Default value :
Default value :
Default value :
Default value :
Default value :
Default value :
Default value :
Default value :
Default value :
Key
set up
Key
set up
Key
set up
Key
set up
9. Lock function
setting
8. Max value
auto holding
7. Set position of
a decimal point
6. Low scale setting
5. High scale setting
1. Set the input range
2. Magnification setting
3. Displayed value error
compensation
4. Display input
average value
keep pushing key(min 2 sec) and
find the parameter 1 set up mode
To move the position of the
number then press key
To move the position of the
number then press key
To move the position of the
number then press key
Key
set up
completed
Key
set up
completed
Key
set up
completed
Key
set up
completed
Key
set up
completed
Key
set up
completed
Key
set up
completed
Key
set up
completed
Key
set up
completed
※ : This is the set-up value when input pulse frequency is within 0.1 second and this value can change if
the input impulse frequency exceeds 0.1 second.
shortly push the button(below 2 sec) and find the parameter 2 set up mode
Display function of
the max input value
Display function of
the min input value
Set up the max
comparative output
value
Set up the min
comparative output
value
Set the comparative
output mode
Hysteresis Selection
Key
Key
Key
Key
set up start
Key
set up start
Key
set up start
Key
set up start
Key
Key
Key
Key
max.
value default
min.
value default
Key
set up
To move the position of the
number then press key
To move the position of the
number then press key
To move the position of the
number then press key
Key
set up
Key
set up
Key
set up
9.999 (set up the max comparative output value)
-1.999 (set up the mix comparative output value)
9.999 (set up the max comparative output value)
-1.999 (set up the mix comparative output value)
LL.ot
99 (max. value)
00 (min. value)
HH.ot
LH.ot
HL.ot
IL.ot
Display of the max
input value
Display of the min
input value
set up the max
comparative output value
set up the min
comparative output value
Set the comparative
output mode
Default value : 01
Key
set up
completed
Key
set up
completed
Key
set up
completed
Key
set up
completed
Key
set up
completed
Key
set up
completed
▒ Lock key ( Key - keep pushing the button(min 2 sec))
Key - keep pushing the button(min 2 sec)
Key
Key
set up start
Key
set up start
Key
set up start
Default value :
Default value :
Set value :
Set value :
Set value :
Set value :
Set value :
Set value :
Key
set up
Key로
설정값 변경
Key로
설정값 변경
Key
set up
OFF
ON
Key
set up
completed
Key
set up
completed
▒ Slope setting method
When users want to display 3600 (min -1999 ~ 9999) within the 1000 Hz input, setting the parameter is as follows.
1. Enter into the parameter 1 by pressing the key for 2 sec
2. Set in the (slop high value) parameter by using shift, up and down key
3. Set in the (slope low value) parameter by using shift, up and down key.
Finish the setting just like above and return to the RUN mode by pressing the menu key.
Parameter 1
Parameter
Set value
▒ Input of peak value and hold by external input
Detect the input peak value through the set-up of parameter or detect the displayed value by
external pressure, or hold the displayed value by external pressure.
: Disuse
: Hold the maximum value
: Hold the minimum value
: Hold by external pressure
▒ Transmission function (Auxiliary output)
● All electrical current : Show the output 4 - 20 ㎃ d.c of current displayed value. (Resolution 12000)
● PNP output (Output of open collector being below 12 - 24 V d.c 50 ㎃)
● NPN output (Output of open collector being below 12 - 24 V d.c 50 ㎃)
● RELAY output (250 V a.c 5 A below) 1a × 3
Dimension and Panel cutout
102.6
▒ MP3-H
▒ MP6-H
Operation
mode
Output operation
Explanation
H : Hysteresis
No output operation
Current indication value ≦ value,
LO output becomes ON.
Current indication value ≧ value,
GO output becomes ON.
Current indication value ≧ value,
HI output becomes ON.
Current indication value ≦ value,
GO output becomes ON.
Current indication value ≦ value,
LO output becomes ON.
Current indication value ≧ value,
HI output becomes ON.
Current indication value ≺ ,
GO output becomes ON.
Current indication value ≧ value,
LO output becomes ON.
Current indication value ≧ value,
HI output becomes ON.
Current indication value ≺ and ,
GO output becomes ON.
Same as the operation but LO output will not
operate under the initial setup value of .
It starts to operate from the next value of .
It does not operate under the initial
Initializing set value
Push the button sequancely with pushing the .
And then is displayed. When displaying , push again the button
and the all default value is initialized.
(* Initializing set value is not available when on.)
▒ Parameter2 ( Key -shortly push the button (below 2 sec)
※ every parameter set up is not available when the on.
▒ How to change the parameter set value
Key - keep pushing the button(min 2 sec)
Key
Key
set up start
Key
set up start
Key
set up start
Default value :
Default value :
Set value :
Set value :
Set value :
Set value :
Set value :
Set value :
Key
set up
Key로
설정값 변경
Key로
설정값 변경
Key
set up
OFF
ON
Key
set up
completed
Key
set up
completed
1. Pressing key more than 2 sec within the RUN MODE will enter into the Parameter 1 and
pressing key less than 2 sec will enter into the parameter 2.
2. Able to select the parameter by pressing , key and within the selected parameter,
parameter and set value repeatedly flickers in the display unit.
3. Able to change the set value by pressing the key and at this moment, set value flickers
in the display unit(when set value is 0, only the 0 th digit of constant value flickers and displayed)
When changing the setting of constant value, able to perform the position shifting by using key.
Example)
When set value is constant, only 0 th digit of the constant value will flicker in the display unit.
In order to change the value on 100 th digit, press the key 3 times. Each time when users press the key,
position of the digit will shirt to the left and selected digit will flicker in the display unit.
When setting is completed, return to the parameter mode by pressing the key. At this moment, flickers the
parameter and set value repeatedly. Able to return to the RUN mode by pressing the key again.
Display value
Input value
