Hanter® Wireless Intelligent Alarm Systems - Model HM2088
12.
Wireless Door Chime
13.
Monitoring service option
by Central Monitoring Station
3.2 Features
1.
Easy installation and simple operation
2.
Wireless and wired compatible
3.
Tampers proof system on telephone line being cut
4.
Priority calling when alarm triggered
5.
Real time record on Central Monitoring System
6.
Press the Emergency Help Button on the Keychain Remote Control to trigger
the siren immediately
7.
Saved data will be retained when power failure
8.
Identifying alarm event by phone, such as illegal entry, fire-alarm or gas leak
9.
Link with Central Monitoring Station through telephone line
10.
Add new accessories with Auto-Setting Code
11. Notified by Wireless Door Chime when there is a visitor
Part 4 –Unit Description
4.1 Standard Accessories:
4.1.1 Control Panel
The Control Panel is a device to receive signal from sensors, switches and
detectors. Once signal received, it will immediately trigger the alarm via the siren
and call the preset telephone numbers or Central Monitoring Station
simultaneously for alarm notification.
a
．
Panel Board Illustration
b. LED indicator light on Panel board (from left to right)
Away Arm
: The LED light is on, while arming outside
Home Arm
: The LED light is on, while arming at home
Alarm:
The LED light is on when alarm is triggered
Power:
The LED light is in red, when power is on and voltage is normal.
When in orange, need to change the battery
P. 5
Hanter® Wireless Intelligent Alarm Systems - Model HM2088
6.5 Wireless Gas Leak Detector
a. Install the detector per the density of gas.
For the Natural gas and piping coal gases lighter than air, install it close to the ceiling
(lower 0.3~1.2meters).
For the liquefied petroleum gases which is heavier than air, install it close to the
floor (higher than 0.3 to 1.2 meters and inside the range of gas source with direct
1.5meters).
b. The detector should not be located near any areas that emit gas (cooking area).
c. The detector should not be located close to any obstacles (curtain or cabinet etc.)
d. The detector should not be located in the bathroom or any area with too much
vapor.
6.6 Coding/ Pairing
The accessories have been coded with the Control Panel and it is ready to be used
directly. The Coding/pairing function is only applicable for additional or new Keychain
Remote control, Door Switches, Motion Sensors and other accessories.
a.
Keychain Remote Control
Step 1: Press the Disarm “
” key of the existing Keychain Remote Control, the
Control Panel entered disarm status
Step 2: Press the “Code” button at Control Panel
Step 3: The Control Panel will emit a “du” sound and release the button
Step 4: Press the
“
” key of the new Keychain Remote Control
Step 5: The Control Panel will emit a 5 “du” sound to acknowledge the coding
successful
Step 6: Continue the Step 4 & Step 5 for the rest of the new Keychain Remote
Controls
Step 7: Exit from Coding program by press the key of
“
”chain Remote Control
b. Door Switches, motion sensors and other accessorie
s
Step 1: Press the Disarm “
” key of the existing Keychain Remote Control, the
Control Panel entered disarm status
Step 2: Press the “Code” button at Control Panel
Step 3: The Control Panel will emit a “du” sound and release the button
Step 4: On or activate the Door Switches, Motion Sensors and other accessories one
by one
Step 5: The Control Panel will emit a 5 “du” sound to acknowledge the coding
successful
Step 6: Exit from Coding program by press the key of
“
”chain Remote Control
6.7 Transmitter Erasing
If you want to erase of all the transmitters (including all sensors and detectors), you
need to cut power and pressing and holding the “Code” button on the Control Panel at
first and then connect the
power plug, when hear “du” voice, release the
“Code” button,
and the transmitters are erased successfully.
P. 16