Hantek 1832C User Manual Download | Manualshive

Page: 18 / 32

background image

15

3.1 Resistance measurement

See the below figure for the connection test.

1. Press the power key to start the instrument.

2. Press the [AUTO/R/C/L/Z] key until Rs/Rp is displayed on the interface which means to select

resistance measurement.

3. Insert the resistor into the test notch, or choose the appropriate test accessories (rubber plug -

alligator clip) and connect it with the measured resistance.

4. Press the [FREQ] key to select the desired test frequency, press [LEVEL] to select the desired

level.

5. Read the measurement results from the screen.

Note: the AC signal is used by the instrument to measure the resistance, so the test result

reflects the AC resistance characteristics of the instrument instead of its DC resistance.

«
...
16
17
18
19
20
...
»

Summary of Contents for 1832C

































Reviews:

No comments

Related manuals for 1832C

Brand: WAGER Pages: 36

Brand: ABQ Industrial Pages: 15

Brand: ABQINDUSTRIAL Pages: 3

Brand: Danfoss Pages: 6

Brand: OHAUS Pages: 19

Brand: OHAUS Pages: 54

Brand: Zenner Pages: 2

Brand: Qu-Bit Electronix Pages: 10

Brand: Raymarine Pages: 42

Brand: Pasco Scientific Pages: 11

Brand: PCB Piezotronics Pages: 16

fieldscout TDR 100

Brand: Spectrum Techniques Pages: 20

Brand: Reed Instruments Pages: 14

MarMonix MSL-765

Brand: Farnell Pages: 15

Brand: Shimadzu Pages: 22

Brand: Televes Pages: 2

Brand: Bluther Pages: 24

Digalox DPM72-MPPA

Brand: TDE Instruments Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands