Hantek 1832C User Manual Download | Manualshive

Page: 15 / 32

background image

12

successful, the secondary display shows "SUCESS"; or it shows "FAILED".

Note: Do not change the state of the test terminals during the correction.

3. Once finished the correction ends, press [REL] key to return to the measurement display.

2.7 Firmware Update

1. Download the tool "DfuSe Demo v3.0.5" and install it. Download upgrade firmware (***. Dfu).

2. In the shutdown state, keep pressing R-X key and insert the USB cable into the Type C port of

the device to connect the device to the computer.

You can see the device is identified in device manager of the PC:

3. Open DfuSe Demo software, click "Choose" button to select the Upgrade firmware (***. Dfu),

and click "Upgrade" to Upgrade it. After finished it, click "Leave DFU mode" to exit the

programming mode.

«
...
13
14
15
16
17
...
»

Summary of Contents for 1832C

































Reviews:

No comments

Related manuals for 1832C

Brand: Bacharach Pages: 87

Brand: Kane Pages: 4

Brand: Eaton Pages: 53

Brand: Oceanic Pages: 75

Brand: Danfoss Pages: 6

Brand: Gazelle Pages: 2

Brand: Halcyon Pages: 36

Sensorex SX41170SI

Brand: Meggitt Pages: 19

Speedrite Fault Finder

Brand: Tru-Test Pages: 2

Brand: MFJ Pages: 9

Radon Scout Home

Brand: SARAD Pages: 2

Brand: RADWAG Pages: 12

Brand: Zamel Pages: 2

Brand: X-Rite Pages: 49

HEAVY DUTY M12 PL

Brand: Milwaukee Pages: 589

ALADIN SPORT PLUS

Brand: ALADIN Pages: 66

Brand: Kurzweil Pages: 24

Brand: Seametrics Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands