Hansol H750D User Manual Download Page 2

TFT-LCD Monitor

2

„

 

Regulatory

    Information

  

 

- FCC Information

 

Caution

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.

  - Canadian Notice

This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations.

  - Avis Canadien

Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du
Canada.

  - Energy Star

As an ENERGY STAR partner, Hansol Electronics Inc. has determined that this product meets energy Star 
guidelines for energy efficiency.

Notice

The information contained in this document is subject to change without notice.

This equipment has been tested and found to comply with limits for a class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation.

This equipment can generates, uses, and radiate radio frequency energy and, if not installed and used in 

accordance with the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation.

If this equipment does cause unacceptable interference to radio and television reception, which can be determined

by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures. 

„

 Reorient or relocate the receiving antenna.

„

 Increase the separation between the equipment and receiver.

„

 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

„

 Consult the dealer or an experienced Radio/TV technician for help.

Summary of Contents for H750D


























Reviews: