Hanseatic XL 30 SSB, User Manual

Page: 34 / 44

GB-3
mix (lubricated petrol). To operate the device the
tank cap must be closed tightly.
6) Start the device at least three meters away from the
place where you fuelled it. Do not smoke during
fuelling or operation and take care that no sparks
or open flames reach into the working area.
DURING OPERATION
• Use this trimmer for its provided purpose only, i.e.
for the cutting of grass, brushwood and weed.
• Avoid any inadvertent starting of the engine. Make
sure, that the control lever is always in ‘Start’
position when you pull the starter rope.
• Always be attentive. To protect yourself and others
from injuries you should not work with this device
if you are tired.
• Do not work with this device under the influence
of drugs, alcohol and medical drugs.
• Always wear protection goggles when operating
this device.
• Wear appropriate clothes. Do not work with this
device with bare feet or open sandals. Always wear
robust footwear with rubber soles. We recommend
to wear gloves, ear protection and long trousers.
•
Do not wear wide clothing or scarves, chains, ties
etc. These may get sucked into the air inlet. Do
also take care that long hair does not get into the
air inlet. Tie long hair together behind the head so
that the neck and shoulders remain free from it.
• Keep your hands, face and feet away from any
moving parts. Do not try to touch or stop the cutting
cord as long as it is turning.
• Use this device in well-ventilated outdoor areas
only. In closed rooms, exhaust gases containing
carbon monoxide may have fatal effects.
• Do not bend forward too far. Always take care to
have a safe stand and good balance.
• Do not touch the exhaust pipe or cylinder. These
parts get extremely hot during operation and
stay hot for some time after the device has been
switched off.
• Always hold the trimmer with both hands during
work. Hold on to both the front and back handle
tightly.
• Check the condition of the cutting head regularly.
All damaged parts must be replaced immediately.
Follow the necessary safety measures when
replacing any parts.
• If you touch an object or get caught (with the
device) switch off the engine immediately and
check the device for possible damage. Repair
possibly existing damages before you try to
continue your work. Do not operate the trimmer if
it has loose or damaged parts.
• Do not run the engine faster than required for
cutting, trimming or the clean-cutting of edges. Do
not let the engine run on high speeds when you are
not cutting.
• The cord protection cover must always be mounted
when the trimmer is operated. If this should not be
the case, the engine may overheat. OPERATE THE
DEVICE ONLY WITH THE PROTECTION COVER
MOUNTED.
• The cutting diameter must not exceed the length
of the protection cover stated in this manual.
• Make sure that the trimmer is not soiled by parts
of plants or other materials.
• Always switch the engine off if you make a break
or move to another area.
• Replace the exhaust pipe and (if necessary) the
spark protector if these are not in proper working
order any more.
• To keep the danger of fire as low as possible the
engine and exhaust pipe must be free from grass,
leaves and excess grease.
• For any interventions, whether maintenance or
repair works, the changing the cutting head or
installation of safety devices, the engine must be
switched off.
• Use original spare parts only. These parts are
available from your appointed retailer. The use
of deviating parts or other parts, accessories or
attachments that are not designed for this trimmer
may result in serious injuries to the persons using
it and your warranty will become void.
• Only use the trimmer with the right trimming cord
installed and with both trimming cords being at the
right length.
AFTER OPERATION
• Clean the trimmer from remainders of grass and
dirt after use.
• Lock the device in a proper place to protect it from
unauthorised use.
FURTHER SAFETY INSTRUCTIONS
• If there is still fuel in the device’s tank do not store
it in a building where the vapours may be ignited
by open fire or sparks.
• Let the engine cool down, before you store the
device in a closed room.
• Lock the trimmer in a proper, dry room to protect
it from unauthorised use and damage.
ASSEMBLY
ASSEMBLY OF THE HANDLE (Fig. 1-2)
1. Assemble the handle holder to the shaft as indicated
by the arrow on the warning label, put the clamps (A)
over the shaft and fix the 2 screws.
2. Put the handle onto the handle holder, then put an-
other clamp (B) over the handle and fix the remaining
2 screws.
Tilt the guiding handle in forward direction until it is in
a convenient working position for you. Then tighten the
screws.
MOUNTING THE PROTECTIVE SHIELD FOR THE
METAL BLADE
(Fig. 3-4)
1. Put the metal protection cover on the gear box and
align it according to the mounting bores. Insert the
screws as shown in Fig. 3 and tighten them firmly.
ATTENTION : Make sure that all components are
mounted and assembled correctly and all screws
are properly tightened.