manualshive.com logo in svg

Hansa C40, Operation, Maintenance And Safety Manual, Page: 19 / 28

Share
Download
Hansa C40 Operation, Maintenance And Safety Manual Download Page 19

 

Hansa C40 O&M Manual 

– OM-013 Revision E 23/10/19

 

© Hansa Chippers 2019 

17 

✓

 

Check wheel nuts and U-bolts are fastened correctly 

✓

 

Check and repack wheel bearings with grease every 12 months 

✓

 

Check air pressure in tires. Inflate to pressure as indicated on the tire 

✓

 

Check safety chains and hitch 

Rotor bearing replacement  

Replacing rotor bearing on engine side of rotor: 

1.

 

Remove engine pulley by unbolting both grub screws in bush. Then screw one grub screw into the third hole and tighten 
until the pulley separates from the bush. Slide bush off the shaft, followed by the pulley.  

2.

 

Remove two grub screws in the bearing. 

3.

 

Remove M16 nuts and bolts bolting the bearing to the housing. 

4.

 

Remove and replace bearing. 

5.

 

When replacing the pulley ensure the rotor pulley is lined up to the engine pulley with a straight edge. Ensure the grub 
screws are tightened evenly so the pulley is tightened evenly. 

6.

 

The  gap  between  the  end  of  the  sensor  and  the  sensing  plate  should  be  approximately  3  mm.  Adjust  the  sensor 
accordingly. If it is set further away, then the sensor may not work properly and therefore the AFC will not work. 

Replacing rotor bearing on inlet chute side of rotor: 

It is recommended to have this bearing replaced by a specialist Hansa dealer. 

Tyre Pressure 

The recommended tyre pressure is 65 Psi. 
 

Summary of Contents for C40





























Reviews:

No comments