Hans Grohe Raindance Showerpipe 27160000, Instructions For Use/Assembly Instructions

Page: 2 / 13

Assembly see page 31
Fault Cause Remedy
Insufficient water - Supply pressure inadequate - Check water pressure (If a pump has been installed
check to see if the pump is working).
- Filters are dirty (96922000) - Clean filter in front of the mixer and on the MTC-
thermo cartridge (96922000)
- Shower filter seal dirty - Clean filter seal between shower and hose
Crossflow, hot water being forced into cold water
pipe, or vice versa, when mixer is closed
- Backflow preventers dirty or leaking - Clean backflow preventers, exchange if necessary
Spout temperature does not correspond with
temperature set
- Thermostat has not been adjusted - Adjust thermostat
- Hot water temperature too low - Increase hot water temperature to 42 ºC to 65 ºC
Temperature regulation not possible - thermo cartridge calcified - Exchange thermo cartridge
Instantaneous heater didn't work with thermostat - Flow limiter in handshower isn’t removed - Remove flow limiter
- Filters are dirty - Clean the filter / exchange filter
- Non return valve hasn’t moved back - Exchange non return valves
Test certificate (see page 37)
Spare parts (see page 37)
Cleaning
(see page 38) and enclosed brochure
Operation
(see page 33)
Flow diagram
(see page 35)

overhead shower

Hand shower
Dimensions
(see page 35)
Maintenance (see page 36)
The non return valves must be checked regularly according to DIN EN
1717 in accordance with national or regional regulations (at least once
a year).
To guarantee the smooth running of the thermostat, it is necessary from
time to time to turn the thermostat from total hot to total cold.
Adjustment
(see page 34)
After the installation, the output temperature of the thermostat must be
checked. A correction is necessary if the temperature measured at the
output differs from the temperature set on the thermostat.
Safety Function (see page 34)
The desired maximum temperature for example max. 42º C can be pre-
set thanks to the safety function.
Do not use silicone containing acetic acid!
Symbol description
Technical Data
Operating pressure: max. 1 MPa
Recommended operating pressure: 0,25 – 0,5 MPa
Test pressure: 1,6 MPa
(1 MPa = 10 bar = 147 PSI)
Hot water temperature: max. 80°C
Recommended hot water temp.: 65°C
Centre distance: 150 mm
Connections G 1/2: cold right - hot left
anti-pollution function
6
Safety Notes
6
Gloves should be worn during installation to prevent crushing and cutting
injuries.
6
The arm of the shower head is intended only to hold the shower head. Do not
load it down with other objects!
6
Children as well as adults with physical, mental and/or sensoric impairments
must not use this shower system without proper supervision. Persons under the
influence of alcohol or drugs are prohibited from using this shower system.
6
Do not allow the streams of the shower touch sensitive body parts (such as your
eyes). An adequate distance must be kept between the shower and you.
6
The product may not be used as a holding handle. A separate handle must be
installed.
6
The shower system may only be used for bathing, hygienic and body cleansing
purposes.
6
The hot and cold supplies must be of equal pressures.
Installation Instructions
• The fitting must be installed, flushed and tested after the valid norms.
• The installation dimensions stated in this installation instructions are ideal for peo-
ple of approximately 1800 mm in body height. The dimensions can be altered if
required. In this case you will have to attend to the minimum height of 2320 mm
from shower tray floor, and alter all the required measurements as necessary.
• Where the contractor mounts the product, he should ensure that the entire area of
the wall to which the mounting plate is to be fitted, is flat (no projecting joints or
tiles sticking out), that the structure of the wall is suitable for the installation of the
product and has no weak points. The enclosed screws and dowels are only suita-
ble for concrete. For another wall constructions the manufacturer’s indications of
the dowel manufacturer have to be taken into account.
• The filter insert (A) must be used to ensure the standard flow rate and to protect
the hand shower against incoming dirt by pipework. Do you want a larger water
flow rate, then you must use the filter packing (B) instead of the filter insert (A).
Incoming dirt leads to defects or/and can damage parts of the hand shower;
such caused faults voids all liability and guarantee claims.
• If required, the bottom part of the pipe between the fixture and the shower head
can be shortened with a fine-toothed saw.
English
4