Hanover TRADTILE2PCFP-RED Manual Download Page 2

Page 2

Outdoor Furniture

1-Year Limited Warranty Program

Contact Warranty Services at

1-800-416-3511

For a period of one (1) year after purchase, the Manufacturer will either repair or replace defective components in accordance with this
Limited Warranty. This warranty is between Manufacturer and the original purchaser and is valid only when accompanied by the
original purchaser’s sales receipt showing original date of purchase and location of purchase. Replacements under this warranty
revert back to the date of original purchase for future warranty.

Manufacturer or its authorized dealer can accept or reject warranty claims based on its findings. This warranty applies in normal
residential use only and is not intended for commercial use. Manufacturer can make substitutions as required of materials,
components, and sub-components of comparable value and utility. This warranty is limited to product repair or replacement (to be
determined solely by Manufacturer). Warranty return is limited to only the single affected component.

This warranty covers only manufacturing defects and does not cover normal wear and tear, damage due to acts of nature (such as, but
not limited to freezing or high winds), abuse or misuse, including chemical damage from suntan oil or other chemicals, exposure to
extreme heat or cold, abrasion or excessive weight. This product is intended to be used in standard installations only. This warranty
is invalid if the product is not used for intended purpose. Manufacturer disclaims liability for any aspect of installation and any
inconvenience caused by a defective part of a component.

Certain items are not covered by this warranty. These include, but are not limited to the following:

1. Components subjected to abuse, including abuse intended to simulate failure.
2. Damages caused by retailer, shipper or installation crew (such as scratches, dents, tears, chips, etc.).
3. Any part which merely exhibits normal wear yet functions essentially as new, including chips, scratches or stretching of

materials and stitching.

4. Tears, punctures, scratches or any damage caused by improper installation or use.
5. Damage to frames/welds resulting from improper assembly or exposure to water and/or sub-freezing temperatures is not

covered. General frame rusting is not covered.

6. Fading and/or discoloration of fabrics/cushions/straps/wicker resulting from exposure to the elements, chemicals, oils, fluids

or any other cause are not covered.

7. Umbrella bases are not covered under any circumstances.
8. Items sold “as is” or floor models.

To make a claim, call the toll-free number below. Please have available a copy of the original sales receipt along with a brief description
of the problem. Please also provide your email address and daytime telephone or cell phone #. Repairs or replacement will be made at
the Manufacturer’s option.

THIS IS THE ENTIRE EXCLUSIVE EXPRESS LIMITED LIABILITY. THE MANUFACTURER NEITHER MAKES NOR IS RESPONSIBLE
FOR ANY OTHER WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING THOSE OF RETAILING DEALERS. THIS
EXCLUSIVE REMEDY IS LIMITED TO RECEIPT OF A CREDIT IN CONNECTION WITH THE REPAIR OR REPLACEMENT OF ANY
PRODUCT OR COMPONENT DEEMED TO BE DEFECTIVE UNDER THE TERMS AND CONDITIONS AS STATED IN THIS
WARRANTY. NEITHER THE PRODUCT MANUFACTURER NOR ITS AGENTS SHALL BE LIABLE IN ANY CASE FOR INCIDENTAL,
INDIRECT, SPECIAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT OR ARISING OUT OF ANY
BREACH OF THIS WARRANTY OR NEGLIGENCE EVEN IF IT HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
EXCEPT AS OTHERWISE MAY BE REQUIRED BY LAW, THERE ARE NO OTHER EXPRESS OR IMPLIED WARRANTIES OTHER
THAN THE WARRANTY DESCRIBED HEREIN, AND ALL OTHER WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF

Sales and use taxes, plus shipping and handling charges are the responsibility of the consumer.

Summary of Contents for TRADTILE2PCFP-RED




















Reviews: