manualshive.com logo in svg

Hanover TRADTILE2PCFP-RED, Manual

Share
Download
Hanover TRADTILE2PCFP-RED Manual Download Page 15

 

10

10. After making any necessary adjustments to the parts, use the hex bolt driver to tighten 

all bolts. Note: each bolt must be tightened a few revolutions at a time. Repeat until all 

bolts are tight. Do not over tighten. Over tightening may strip bolts. Cover all bolts with 

covers. 

 

11. Note the clear bumpers spaced evenly throughout the inside of the table top. Carefully 

place tiles inside table rim, resting on the clear bumpers as shown in Figure 11 

                                                               

Figure 11 

 

12. Pour the lava rocks into the burner completely covering the burner. See Figure 12 

 
 

 

 

 

 

 

Ignition Well 

 

13. Remove the cardboard cover from the ignition well as shown in Figure 13. Remove 

any lava rock or fire ice on top of ignition well. 

 

 
                                                                                                                                             

 
 
   
               

Cardboard Cover

 

 

Figure 12

 

Figure 13

 

Summary of Contents for TRADTILE2PCFP-RED




















Reviews:

No comments

Brands by name

Popular brands

Load more brands