background image

  

PLAN AHEAD

Site Selection

l

Avoid  overhanging  trees  as  much  as  possible  as  leaves  will  make  regular  cleaning

necessary and broken branches are a potential hazard.

l

Small trees,bushes or fences nearby can be helpful,acting as a wind break.

Site Preparation

The  site  must  be prepared  so  that the base of  the  shed  is  level  all  round  and checking
with a spirit level is required.

The base can be constructed by treated timber or concrete,in order to stop the moisture
getting into the shed.

The shed is not designed to be built onto lawn directly

.

Also the

ground will get muddy during rainy days.

If  a  concrete  pad  is  made,it  is  important  that  this  slopes  towards  the  edges  to  prevent

water ingress.
Time must be allowed for any concrete or cement to dry before building the shed on top.

Bases can also be constructed from bricks,blocks,or mounted on a concrete pad.

The  bricks or blocks  should be  cemented  onto  firm and  level  concrete  footings  and the
greenhouse frame drilled and screwed to the base.

IMPORTANT NOTES:

l

Find  someone  to  help  you:it  is  much  easier  with  someone  to  hold  parts,pass  tools

ect.Also  some  steps  require  two  people  to  lift  structures  together.This  is  not  very

heavy work so would suit most able-bodied people.

l

Allow  plenty  of  time:rushing  often  causes  errors  and  the  re-doing  of  incorrect

assemblies.If you have never built a shed before,it can take most of a day to carefully
complete the construction.

l

Have the right tools to hand.

l

Safety clothing as recommended in the 'Tools' section.

l

Ideally  lat  out  the  parts  and  check  that  all  are  present  before  commencing

construction.Lay on cloths or plastic sheets if there is any risk of scratching the parts.

l

Tighten  all  nuts  carefully,being  sure  not  to  miss  any.Check  the  frame  is  square  and

using a spirit level to check that it is upright.

sharp edges

when assembling or performing.

wear work gloves, long sleeves and eye glasses,

Pay attention to the sharp edges. Please

Summary of Contents for HANAPEXSHD-GW
















Reviews: