background image

Page 4

ASSEMBLY INSTRUCTIONS

COVER

FOOT CAP

B

A

1

2

Important: We recommend 2 people work together to assemble the chair.

If chair frame has been properly positioned

on the rocker assembly, all arrows on the "U" bar and rocker assembly will be pointing in the same direction.

Note the arrow labels on the "U" bar

and the rocker assembly. Also note the horseshoe shape of the rocker plate. Point the open end of the horseshoe
away from you. The arrows on the rocker assembly should be pointing towards you. Set the chair frame on the
rocker assembly with front of the seat facing you and the arrows on the "U" bar pointing towards you as shown in

. This is very important for a safe, balanced rocking motion.

Figure 1

Critical Step: The "U" metal plates must be installed in the proper location.

Hand tighten nuts 3-4 revolutions only.

CAUTION: Failure to place "U" metal plates under the rocker plates and above the"U" bar exactly as shown
in the diagram will cause the bolt heads and nuts to damage the structure of the rocker plates and the "U" bar.
Damage due to over tightening of bolts or improper assembly could cause injury and may void your warranty.

Insert the "U" metal plates, so that the "U" bar and rocker plate are between both sides of the "U" metal plates. Make
sure that the holes in the "U" metal plate are completely aligned with the holes in the "U" bar as shown in

.

Guide the bolts through the holes on the top side of the "U" metal plate, through the holes in the "U" bar, through the
holes in the rocker plate and then, most importantly, through the holes in the bottom side of the "U" metal plate. It is
very important that the holes in the bottom of the "U" metal plate are placed directly beneath the holes in the rocker
plate. Add a spring washer and a nut to each bolt as shown in

.

Repeat the same procedure on the other side.

Read this step and carefully examine.

Figure 2

Figure 2

3

Tighten all nuts and bolts with the hex wrenches provided.

Remove arrow labels

from "U" bar and rocker assembly. Cover bolts with bolt covers.

Bolts must be FULLY tightened.

Figure 2

F

C

D

E

F

"U" BAR

Figure 1

"U" BAR

ROCKER

ASSEMBLY

ROCKER PLATE

G

Assembly detail shown from the REAR of the chair for clarity

CHAIR VIEWED FROM THE FRONT

Summary of Contents for Fontana FNTDN7PCSW2C









Reviews: