Programming of the Track
The programming should be done during STOP mode
1. Press the
MODE
button, the LCD display will show
P01
.
2. Use the
SKIP UP
or
SKIP DN
button to select the desired track.
3. Press the
PROGRAM
button again to store the selected track in the memory, the
LCD display will show
P02
and flash continuously.
4. Repeat step 2 to 3 to store more tracks in the memory. You can store up to
20
tracks
in the memory for CD disc and
99
tracks in the memory for MP3 files.
5. Press the
PLAY/PAUS
E button to start playing the disc in the programmed order.
6. To stop playing, press the
STOP/USB
button.
7. To cancel the programming list, press the
STOP/USB
button and set the
FUNCTION
switch to
OFF
position.
BLUETOOTH STREAMING
1. Set the
FUNCTION
switch to
BT/AUX
position. The LCD display will show “
bt
” and
the bluetooth icon will flash.
2. Turn on your Bluetooth of your Bluetooth device and search the boombox for
connection. Your Bluetooth device should find “
HX-312CD HANNLOMAX
”.
3. If the connection is successful, the bluetooth icon on the display will stop flashing.
4. Select and play the audio files though your Bluetooth device.
5. To stop this function, switch to other mode or shut down your Bluetooth of your
Bluetooth device
BLUETOOTH STREAMING THROUGH NFC PAIRING
1. Set the FUNCTION switch to
BT/AUX
position. The LCD display will show “
bt
” and
the bluetooth icon will flash.
2. Enable your
NFC
function of your Bluetooth device and place the device near the
NFC sensor
on the CD door for 5 to 10 seconds.
3. If the connection is successful, your Bluetooth device
will show that it is connected and the bluetooth icon
on the LCD display will stop flashing.
4. Select and play the audio files though your Bluetooth
device.
5. To stop this function, switch to other mode or shut
down your Bluetooth of your Bluetooth device
AUTO PAIRING
Once the unit paired with the Bluetooth device, it will automatically pair with that device
next time when you turn on the unit and that Bluetooth device.
IMPORTANT NOTE ( FOR EUROPEAN VERSION ONLY)
Automatic standby switching
To comply with the ERP2 directive, the unit automatically switches to standby after
approximately
10 minutes
without a signal. To switch the unit on again, tap the function
switch to off mode and then your desired function mode.
- EN 6 -
TROUBLE SHOOOTING
Symptom
Possible Problem
Solution
AC power cord is not plugged
properly into a wall outlet or
the connector is not plugged
into the AC Socket on the back
of the System.
Re-plug the AC power
cord into the wall outlet
and the connector into AC
Socket on the System.
Unit does not
respond (no power)
Wall outlet is not functioning.
Plug another device into
the same outlet to confirm
the outlet is working.
Radio no sound
Unit not in RADIO function
mode.
Volume set at minimum
Tap FUNCTION button to
RADIO position.
Increase Volume
Noise or sound
distorted on FM
broadcast
Station not tuned properly for
FM.
FM: Wire antenna is not fully
extended.
Retune the FM broadcast
station.
FM: Fully extend or reposition
the FM wire antenna.
CD disc does not
play
Unit not in CD function
mode.
Audio disc is installed
incorrectly.
It the disc is self-compiled, the
media used may not be
compatible with the player.
Select CD mode.
Insert audio disc with label
side up.
Use better quality blank media
and retest.
Audio disc skips
while playing
Disc is dirty or scratched.
Wipe disc with clean cloth or
use another disc.
Intermittent sound
from the player
Dirty or defective disc
Dirty pick up lens
Player is subject to excessive
shock or vibration
Clean or replace the
defective disc
Use a lens cleaning disc to
clean the lens
Relocate the player away
from shock or vibration
Unit gets warm after
extended play at
high volume
This is normal.
Turn the unit off a period
of time or lower volume.
Unit Switch off
automatically
The units goes to STANDBY
mode after 10 minutes without
any signal
Tap the function switch to
off mode and then your
desired function mode.
SPECIFICATIONS
Frequency Range:
FM 87.5 - 108 MHz
Power Supply:
AC 100-240V ~ 50/60Hz
DC 12V
(UM-2 x 8)
Specifications are subject to change without further notice.
- EN 6 -
