Hanna Instruments HI99111 Instruction Manual Download Page 17

Page: 17 / 20

ACCESSORIES

ELECTRODE

MAINTENANCE

ELECTRODE MAINTENANCE

PREPARATION

• Remove the protective cap. Do not be alarmed if any salt

deposits are present. Rinse with water.

• Shake the electrode down as you would do with a

clinical thermometer to eliminate any air bubbles inside

the glass bulb.

• Remove the fill hole cover to ensure the reference junctions

are flowing. Set aside for storage.

• Top off the electrolyte filling solution using

HI7082

solution.

• If the bulb and/or junction are dry, soak the electrode

HI70300

Storage Solution for at least 30 minutes.

• Rinse with water.

• Calibrate before using.

STORAGE

• To ensure a quick response, the glass bulb and the junction

should be kept moist and not allowed to dry.

Code and
serial number
on the other
side

Temperature

sensor

Quick connector with
Rubber protection, and
1 meter cable

Reference

junction

pH bulb

Summary of Contents for HI99111





















Search results

Summary of Contents for HI99111

Reviews:

Related manuals for HI99111

Brands by name

Popular brands

Hanna Instruments HI99111, Instruction Manual

Search results

Summary of Contents for HI99111

Reviews:

Related manuals for HI99111

Brands by name

Popular brands