background image

Hanna Instruments reserves the right to modify the design, construction or appearance of its products without advance notice.

CERTIFICATION

All Hanna Instruments conform to the 

CE European Directives.

Disposal of Electrical and Electronic Equipment. 

The product should not be treated as household waste. 

Instead, hand it over to the appropriate collection point for the recycling of electrical and electronic equipment, 

which will conserve natural resources.

Disposal of waste batteries.

 This product contains batteries, do not dispose of them with other household 

waste. Hand them over to the appropriate collection point for recycling. Ensuring proper product and battery 

disposal prevents potential negative consequences for the environment and human health. For more information, 

contact your city, your local household waste disposal service, or the place of purchase.

Regulatory Notices for the stand-alone, Bluetooth, low-energy module.

United States (FCC)

 FCC ID: 2AA9B04. This device complies with FCC Rules, Part 15 Subpart C “Intentional Radiators” 

and Subpart B, Chapter §15.105. This equipment has been tested and found to comply with the limits for a Class A 

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against 

harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, 

and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may 

cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause 

harmful interference in which case, users are required to correct the interference at their own expense.

Canada (ISED)

 IC: 12208A-04. This device complies with Industry Canada license exempt RSS standard(s). Operation 

is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any 

interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme 

aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux 

conditions suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout 

brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.

Australia / New Zealand (RCM)

 BMD-300 complies with the AS/NZS 4268:2017.

Japan (MIC) 

South Korea (KCC) 

R-CRM-Rgd-BMD-300

Brazil (ANATEL)

: Contains ANATEL approved module # 00820-21-05903.

Mexico (IFETEL)

: Este equipo contiene el módulo con IFT #: NYCE/CT/0146/17/TS.

Summary of Contents for HALO 2 HI9810362













Reviews: