manualshive.com logo in svg

Hanna Instruments C 214, Instruction Manual, Page: 39 / 40

Share
Download
Hanna Instruments C 214 Instruction Manual Download Page 39

39

• Replace the cap tightly and shake the vials vigorously for about

30 seconds until all the powder is completely dissolved.

•

Insert the vials into the reactor and
heat them for 30 minutes at 105°C.

Note

: to obtain most accurate

results, it is strongly recommended
to remove the vials frome the reactor
after exactly 30 minutes.

•

At the end of the digestion period
switch off the reactor, place the vials
carefully in the test tube rack  and
allow to cool to room temperature.

Warning

: as the vials are still hot, be

careful in handling them.

• Select the program number corresponding to Total Nitrogen LR on the

secondary LCD by pressing PROGRAM 

t

 and 

s

.

•

Remove the cap from the vials and add the content of one packet
of Sodium Metabisulfite for Total Nitrogen analysis to each vial.
Replace the cap tightly and shake gently the vials for 15 seconds.

•

Wait for 3 minutes (without shaking the vials)
to allow the reaction to complete.

Nitrogen, Total LR

42

NITROGEN, TOTAL HIGH RANGE

SPECIFICATIONS

Range

10 to 150 mg/L

Resolution

1 mg/L

Precision

±3 @ 75 mg/L

Typical EMC

±1 mg/L

Deviation
Light Source

Tungsten lamp with narrow band interference filter
@ 420 nm

Method

Chromotropic acid method. A persulfate digestion
converts all forms of nitrogen to nitrate. Then the
reaction between nitrate and the reagents causes
a yellow tint in the sample.

REQUIRED REAGENTS

Code

Description

Q.ty/test Q.ty/set

*

Digestion Vial

1 vial

50 vials

---

Deionized Water

0.5 mL

1 bottle

---

Potassium Persulfate

1 packet

50 packets

---

Sodium Metabisulfite

1 packet

50 packets

HI 93767-0

Total Nitrogen Reagent 1 packet

50 packets

**

Reagent Vial

1 vial

50 vials

*

Digestion Vial identification

: 

N

, 

red 

cap.

**

Reagent Vial identification

: 

N

, 

white 

cap.

Note

: Store the unused vials in their container in a cool and dark place.

REAGENT SET

HI 93767B-50

Reagents for up to 49 tests. Contains:
Box 1: HI 93767B-50 Reagent Set
Box 2: HI 93767A&B-50 Reagent Set, for both

HI 93767A and HI 93767B parameter.

For other accessories see page 77.

REQUIRED ACCESSORIES

C 9800-01

Hanna reactor (115 VAC)

C 9800-02

Hanna reactor (230 VAC)

HI 740216

test tube cooling rack (25 holes)

HI 740217

Laboratory bench safety shield

For other accessories see page 77.

Nitrogen, Total HR

Summary of Contents for C 214









































Reviews:

No comments