manualshive.com logo in svg

Hanna Instruments C 214, Instruction Manual, Page: 1 / 40

Share
Download
Hanna Instruments C 214 Instruction Manual Download Page 1

Instruction Manual

C 214

Multiparameter Bench

Photometer

for

Wastewater Treatment

Application

w w w . h a n n a i n s t . c o m

These Instruments are in

Compliance with the CE Directives

MANC214R3   10/04

TECHNICAL SERVICE CONTACTS

Australia:

Tel. (03) 9769.0666 • Fax (03) 9769.0699

e-mail: [email protected]

China:

Tel. (10) 88570068 • Fax (10) 88570060

e-mail: [email protected]

Egypt:

Tel. & Fax (02) 2758.683

e-mail: [email protected]

Germany:

Tel. (07851) 9129-0 • Fax (07851) 9129-99

e-mail: [email protected]

Greece:

Tel. (210) 823.5192 • Fax (210) 884.0210

e-mail: [email protected]

Indonesia:

Tel. (21) 4584.2941 • Fax (21) 4584.2942

e-mail: [email protected]

Japan:

Tel. (03) 3258.9565 • Fax (03) 3258.9567

e-mail: [email protected]

Korea:

Tel. (02) 2278.5147 • Fax (02) 2264.1729

e-mail: [email protected]

Malaysia:

Tel. (603) 5638.9940 • Fax (603) 5638.9829

e-mail: [email protected]

Norway:

Tel. (23) 3811.00 • Fax (23) 3811.01

e-mail: [email protected]

Singapore:

Tel. 6296.7118 • Fax 6291.6906

e-mail: [email protected]

South Africa:

Tel. (011) 615.6076 • Fax (011) 615.8582

e-mail: [email protected]

United Kingdom:

Tel. (01525) 850.855 • Fax (01525) 853.668

e-mail: [email protected]

USA:

Tel. (401) 765.7500 • Fax (401) 765.7575

e-mail: [email protected]

For additional Technical Support in your local lan-
guage, see 

www.hannainst.com

Summary of Contents for C 214









































Reviews:

No comments