Hanil Ultra 5.0 Operating Manual Download Page 13 | Manualshive

Page: 13 / 20

background image

4. Operation

4.5 Setting RPM/RCF

4.6 Setting run time

4.7 Setting Accelation/Deceleration rate

4.9 End the centrifugation

①

Press Stop ( ) key to stop centrifugation.

①

Press the RPM ( ) button or RCF ( ) button.

②

Press the numeric key to set desired RPM/RCF.

③

Press the Enter ( ) button to fix the value.

①

Press the Time ( ) button.

②

Press the numeric key to set centrifugation time.

③

Press the Enter ( ) button to fix the value.

①

Press the Accel ( ) key or ‘Decel ( )key.

②

Press the Numeric keys to select the Acc/Dec step.

▶

The higher the setting step, the faster the deceleration speed.

▶

Decelstep‘0’meansnaturalbrake.

4.8 Start the centrifugation run

①

Check the all parameters are correct and the lid is closed.

②

Press Start ( ) button.

sales

@ihanil.com / [email protected] l 12

«
...
11
12
13
14
15
...
»

Summary of Contents for Ultra 5.0





















Reviews:

No comments

Related manuals for Ultra 5.0

Brand: Omnia Pages: 8

ImageQuant LAS 4000

Brand: GE Pages: 86

Brand: GE Pages: 160

Brand: GE Pages: 134

Brand: Parata Pages: 40

Brand: Rapala Pages: 14

Brand: S.R.Smith Pages: 43

Brand: Yetter Pages: 24

Brand: Yetter Pages: 32

Brand: RainPoint Pages: 40

Brand: FARM-MAXX Pages: 35

Brand: Wayflex Pages: 11

KONTROL KUBE ABACUS

Brand: FIBERLOCK Pages: 8

Brand: Gronomics Pages: 2

Brand: Monosem Pages: 92

Brand: Otto Bock Pages: 252

Brand: Original BTC Pages: 2

Brand: ResMed Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands