HANGCHA CPCD10N-RW10 Operation And Maintenance Manual Download | Manualshive

Page: 59 / 108

background image

55

19

、

warning label

Do not load lift truck over capacity limit designated on the load chart.Do not lift unstable loads.

This lift truck is not designed for raising or transporting people.Do not use lift truck for those purposes under any

Before you get off lift truck,made sure the hand brake is set,lower forks or attachments,put forward/reverse lever
in neutral position and turn off key switch.Do not park on a slope.

circumstances.

Repair work should be done by authorized and trained persons only.

SERIOUS OR FATAL INJURY MAY RESULT TO YOURSELF OR OTHERS IF NOT FOLLOWED

This lift truck should not be operated by anyone who is not authorized and properly trained.

Read the Operators Manual and all warnings carefully,and make yourself familiar with your lift truck.

Inspect and check your lift truck daily before and after use.Do not operate faulty or damaged lift trucks.

To protect from falling objects,make sure that the Overhead Guard and Load Backrest Extension are correctly mounted

and in good condition.

Before starting engine,always set forward/reverse lever in neutral,with hand brake on .
Drive carefully,keeping forks and attachments as low as possible & fully tilted backp- Never Forward

Keep a careful lookout for people,obstructions and the path of travel.Watch clearance,especially overhead and tail
swing.Yield right of way to pedestrians.

Drive forward when you are climbing a slope with a load .Drive in reverse when you are descending with loads.Do not

Slow down before turning.Avoid any sudden start,stop or turning.Lateral tipover can occur if truck is improperly operated.

Do not stick hands,feel and other parts lf your body outside the Operators compartment.

Operator's Manual and Service Manual are supplied with this truck or available from our forklift truck dealers.

turn while on a slope.

21

、

fan cuts hand label

22

、

belt nips hand label

23

、

noise label

L

WA

24

、

hydraulic oil label

25

、

hang label

：

express the hang position and method. When hanging, the rope

should not touch the light and even destroy it.

«
...
57
58
59
60
61
...
»

Summary of Contents for CPCD10N-RW10













































































































Reviews:

No comments

Related manuals for CPCD10N-RW10

Brand: Strongway Pages: 23

Brand: Land Pride Pages: 28

Brand: UniCarriers Pages: 161

Brand: SolidHub Pages: 24

Brand: Gradall Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands