Page 22
BG44 Boiler Gun Operating Manual
a) Turn off the air supply at the source. Dis-
connect the air hose assembly from the
machine.
b) Turn the locking wrench to loosen the
locking system from the workpiece.
c) Slide the BG44 straight out from the
workpiece using the body of the machine
to support it’s weight.
WARNING
Always pick up and move the BG44 Boiler
Gun by body of the machine. Never pick up
the BG44 Boiler Gun by the throttle lever
section of the air motor, actuation of the
motor could occur and lead to severe injury.
Never pick up the BG44 Boiler Gun by the
air hose assembly as it could become
detached and result in injury or damage to
the machine. Do not pick up and move the
machine by either of the wrenches as
damage to the machine could occur.
4.2.2
Electric motor
To operate the BG44 Boiler Gun with the electric motor
do the following:
1. Start the motor by squeezing and holding the
trigger.
2. With the other hand turn either the crank han-
dle or feed wrench to advance the cutting tool
into the workpiece.
3. Continue to turn either the crank handle or feed
wrench until the required machining is com-
plete. Base the feed rate on the machine’s
feedback, if the RPMs drop or the motor stalls
slow the feed rate.
4. Once complete, allow the machine to make a
few revolutions without feeding the cutting tool
to clean up the machined surface.
5. Release the trigger to stop the machine.
6. Reverse the rotation on the crank handle or
feed wrench 2-3 revolutions to back the cutting
tool away from the workpiece. The ratchet
mechanism on the feed wrench will need
switched to feed out instead of in.
7. To remove the BG44 from the workpiece do the
following:
a) Unplug or disconnect the power supply
from drive motor. Lock out/tag out where
applicable.
b) Turn the locking wrench to loosen the
locking system from the workpiece.
c) Slide the BG44 straight out from the
workpiece using the body of the machine
to support it’s weight.
WARNING
Always pick up and move the BG44 Boiler
Gun using the body of the machine or
combination of the center shaft and
machine body. Never pick up the BG44
Boiler Gun by the handle section of the
electric driver, actuation of the motor could
occur and lead to severe injury. Never pick
up the BG44 Boiler Gun by electrical cord as
it could result in damage to the machine.
Do not pick up and move the machine by
either of the wrenches as damage to the
machine could occur.
F
IGURE
4-2. BG44
WITH
ELECTRIC
MOTOR
Summary of Contents for BOILER GUN BG44
