background image

-35-

DECAL LOCATION

Your H&S 

Top Shot

 

was manufactured with operator safety in mind. Located on the 

Top Shot

 

are 

various decals to aid in operation, and to warn of danger or caution areas. Pay close attention to all the 

decals on your 

Top Shot

.

DO NOT REMOVE ANY OF THESE DECALS. IF DECALS ARE LOST, DAMAGED, OR 

IF YOUR 

TOP SHOT

 IS REPAINTED, REPLACE DECALS. 

REMEMBER: DECALS ARE FOR YOUR PROTECTION AND SAFETY.

Listed below are the decals on your 

Top Shot

. These decals may be ordered individually by part number, 

or by ordering as a complete set.
Part #     Quantity 

Description

311 

 

Patent Decal

1494A   

Do not operate this machine if this decal is exposed. Replace safety shields

1494B  

Do not remove shields - moving parts inside

1494J   

Do not clean or work on the machine without first disengaging power

1494K  

Do not remove shields - moving parts inside

3494A   

Remote Grease Decal

5896B  

Rotating driveline

71064  

H&S/

Top Shot

 Decal - Side

71085  

H&S/

Top Shot

 Decal - Rear

71068   

5220 Model # Decal - Side

71070   

5226 Model # Decal - Side

71096  

H&S/

Top Shot

 Decal - Front

71090   

5220 Model # Decal - Front

71091   

5226 Model # Decal - Front

8515   

Degree of Angle Decal-PTO Shaft

9194A   

No step - stay clear

9194B  

Never Allow Riders On This Machine

11210B 

Do not remove shields

11599   

Do not go near leaks

32320   

Spiral Decal for Main Auger Shaft-Rear

51010   

Pinch Point

54033   

Made in USA 3”

58703   

Stay Clear of Beaters

66076   

Located Behind Shield

71188B 

Jack Storage Position

72203A 

Help avoid injury - Read and understand the operators manual

82602   

Crushing Hazard

081312 

Located behind sprocket

093020 

16 

Grease zerk decal

093366 

Operators Manual

102196 

Lube-CV Joint

111209A 

Pinch Point

111209B 

Stay clear of expeller when rotating or if tractor is running

111209C 

Keep Out - Disengage all power and shut off tractor engine

11210A 

Discharge gate opening decal

11211176 

Shear Bolts - Remove broken shear bolt before replacing

DCAMB 

Amber Reflector

DCRED 

Red Reflector

LW112901 

Auger Height Indicator Decal

TFM97  

SMV  Decal

Summary of Contents for 5220















































Reviews: