background image

 

13

9. The safety edges 

 
Two direction-sensitive safety edges and one general safety edge have been 
included in the Handicare Xclusive. 
 
The direction-sensitive safety edges 
 
The direction-sensitive safety edge prevents the lift from moving further in the 
direction that is blocked. 
However, the Handicare Xclusive can still be moved in the opposite direction to 
remove the blockade. 
The diagnostic code shows “4” or “6” 
 
The following switches have been included in the direction-sensitive safety edge: 
 

  Footrest switches 

  Detection switches for the power pack 

  Detection switches for the front chassis 

 
The handing of the safety edges is when sitting on the lift. 
 
The general safety edges 
 
The general safety edge prevents the lift from moving further in both directions. 
 
The diagnostic code shows “0” when the toggle is moved in either direction when the 
safety edge is obstructed. 
 
The following switches have been included in the general safety edge: 
 

  Seat swivel switch 

  Overspeed governor switch 

  Key switch  

  The emergency stop  

 
When the key switch or  the emergency switch are activated, nothing will function 
When the safety brake or the seat swivel  switch are activated the lift won’t move, but 
the option automatic swivel and powered footrest are still operable. 

Summary of Contents for Xclusive




















Reviews: