background image

 

 

 CS-684 operation manual

 

 

 

issue 1 16.08.02                                                                                                               

                        P.13 of 13

 

Trouble Shooting

 

 
 

Problem 

Cause 

solution 

No power to 

individual parts 

Fault with power cord or plug 

Check the power connection 

Circuit breaker tripped 

Reset the breaker and investigate the 
system 

Main power supply not switch on 

Switch on the main power supply 

Bad contact 

Check the circuit if there is any loosen 
part 

Transformer fault 

Check the voltage of power supply 

Temperature monitor 

unsteady 

Thermocouple fault 

Replace the temperature sensor 

Thermocouple connection is loosen 

Check and tighten the connection 

Temperature controller malfunction 

Replace the circuit board in the control 
box 

Thermocouple extension cable short 
circuit 

Check the break point and repair 

Thermocouple installed in wrong 
position 

Check the end point of the sensor and 
relocate the position of it 

Temperature monitor 

showing the ambient 

temperature 

Heater not started up 

Press the heat button 

Thermocouple fault 

Replace the thermocouple 

Power supply voltage unsteady 

Install voltage stabilizer 

Heater temperature 

cannot raises up 

Solid state relay (SSR) malfunction 

Replace the SSR 

Compressed air pressure too low and 
interlocked 

Increase the compressed air pressure 

 

Summary of Contents for CS-684















Reviews: