background image

   

              

          User Manual RDx-xxxDT-10.31 

 

 

Page 5 of 8

                                                                                                                                      

www.hanbayinc.com | 1 800 315 4461        

Rev.2020.4                                                                                                                                                                                               

 

[email protected] 

Functionality of the RDx-xxxDT: 
 

The RDx can operate as a 3-position or 4-position actuator. The 4

th

 position is enabled by turning Dip 8 ON. 

 

3-pos Functionality (Dip 8 OFF) 

 

Input#1 

(Pin 1) 

Input#2 

(Pin 2) 

Action taken 

High 

High 

Moves to or remains in center position 

Low 

High 

Moves to or remains in right position 

High 

Low 

Moves to or remains in left position 

Low 

Low 

Moves to or remains in right position (Input#1 has 
precedence over Input #2) 

 

The feedback from the RDx-xxxDT is as follows: 

Output#1 

(Pin 3) 

Output#2 

(Pin 4) 

Meaning   

High = 4.5vDC   Low = 0.8vDC 

High 

High 

Actuator output is in center position 

High 

Low 

In Right position  

Low 

High 

In Left position  

Low 

Low 

Actuator is moving, or has stalled and given up trying to 
reach a requested position. 
You may retry to reach any position by cycling alternate 
inputs and trying the original again. Repeated failures to 
reach the position will require troubleshooting. 

 
4-pos Functionality (Dip 8 ON) 
 

Input#1 

(Pin 1) 

Input#2 

(Pin 2) 

Action taken 

High 

High 

Moves to or remains in center position 

Low 

High 

Moves to or remains in right position 

High 

Low 

Moves to or remains in left position 

Low 

Low 

Moves to or remains in back position 

 

 

 

The feedback from the RDx-xxxDT is as follows: 

Output#1 

(Pin 3) 

Output#2 

(Pin 4) 

Meaning   

High = 4.5vDC   Low = 0.8vDC

 

Low 

Low 

Actuator is at requested position  

High 

Low 

Actuator is moving  

Low 

High 

Actuator has stalled. The stall can be cleared by making 
the actuator turn in the other direction. 

 

Direction of rotation and using Input 1 
 

To change the direction of rotation on the actuator change the setting on Dip12 and power up the actuator again. 
 
 

 

VERY IMPORTANT:

 Input 1 must always be used if only one input is used to operate the valve. 

When the actuator is operated using input 1 an automatic calibration is done every time the valve 
is actuated. This does not happen on input 2. 

 
 

Right 

Top View 

onto valve or 

other 

appliance 

Center 

Back 

Left 

Top View 

onto valve or 

other 

appliance 

Center 

 

Right 

Left 

Summary of Contents for RD-DT-10.31 Series









Reviews: