background image

 

User Manual MCx-xxxAS-1.05 

 

 

 

Page 18 of 18

                                                                                                                        

www.hanbayinc.com | 1 800 315 4461      

Rev.2021.8                                                                                                                                                                              [email protected] 

LABEL BREAKDOWN 

 
 
 

 

 

  
 
 
 
 
 

 

Actuator Series

 

 

M-Series or R-Series

 

Actuator Supply Voltage 

 

12-24 VDC @ 3.0 A or

 

110-240 VAC @ 1.5 A

 

Circuit Board Version

 

Ax-8.09

 

Dx-10.31

 

Dx-4.10 (Obsolete since 2019)

 

Px-10.3

 

Actuator Part Number

 

Refer to part number breakdown 
for available options.

 

QR Code

 

Scan this QR code for a 
direct link to the user 
manual for your unit!

 

Actuator Serial Number

 

This serial number is unique for 
each individual unit and is directly 
tied to your order/invoice number.

 

Firmware Version

 

AF-1.05     MM = Multiturn

 

AB-1.05     MML = Multiturn Low Torque

 

AS-1.05     MMUL = Multiturn Extra Low Torque

 

                  QM = Quarter turn

 

                  QM97 = Quarter turn 97°

 

DT-2.01

 

DC-2.01

 

DT-4.06 (Obsolete since 2019)

 

M-Dx V2.31

 

Summary of Contents for MC-AS-1.05 Series



















Reviews: