Hanatek MFI 4050 Operating Manual Download Page 31 | Manualshive

Page: 31 / 39

Hanatek MFI 4050 Operating Manual Download Page 31

MFI 4050

V1.3

31

When the MFI instrument is not in use it should be powered down. This will leave
the instrument in a safe state with the test mass lowered. Remove the test piston
or the cleaning probe if fitted to the test weight. In the system menu press the off
button.

Calibration

The  Hanatek  MFI  is  supplied  calibrated.  We  recommend  re-certifying  the
instrument  annually.  This  can  be  done  by  a  Hanatek  approved  calibration
engineer  or  the  user  can  self  certify  the  instrument  using  a  Hanatek Calibration
pack.

The calibration pack will enable the user to calibrate the instrument using UKAS
certified calibration artefacts.

The re-calibration kit consists of the following certified parts:

Calibration Probe (replaces existing probe)
Standard Testing Die (replaces existing Die)
Standard Testing Piston (replaces existing Piston)
Replacement inner Barrel (replaces existing Inner Barrel)
Cleaning Patches
Barrel Removal Tool

Step 1

«
...
29
30
31
32
33
...
»

Summary of Contents for MFI 4050








































Reviews:

No comments