background image

LEAK TEST

1. Make 2-3 oz. of leak test solution

detergent and three parts water).

2. Apply several drops of solution

where hose attaches to regulator.

3. Apply several drops of solution

where regulator connects to cylinder.

4. Make sure all patio heater valves are OFF.

5. Turn cylinder valve ON.

IF BUBBLES APPEAR AT ANY CONNECTION, THERE IS A LEAK.

1. Turn cylinder valve OFF.

2. If leak is detected at hose/regulator connection, tighten connection and

perform another leak test. If bubbles continue to appear, call our customer

service desk at 

3. If leak is detected at regulator/cylinder valve connection, disconnect,

reconnect, and perform another leak test. If you continue to see bubbles

after several attempts, cylinder valve is defective. Call our customer service

desk at 

IF NO BUBBLES APPEAR AT ANY CONNECTION, THE CONNECTIONS ARE SECURE.

Note: 

Whenever gas connections are loosened or removed, you must 

perform a complete leak test.

Caution: 

Do not attempt to 

operate this appliance until you 

have read and understand all 

Safety Information in this manual 

and all assembly is complete and 

leak tests have been performed.

 WARNING

 Perform all leak tests outdoors.

 NEVER leak test when smoking
 Do not use heater until all connections 

have  been leak tested and show no signs
of leakage.

BEFORE TURNING GAS SUPPLY ON:

1. Your heater was designed and

approved for 

OUTDOOR use

only

. Do NOT use it inside a

building, garage, or any other

enclosed area.

2. Make sure surrounding areas are

free of combustible materials,

3. Ensure that there is no

obstruction to air ventilation. Be

sure all gas connections are tight

and there are no leaks.

4. Be sure the cylinder cover is

clear of debris. Be sure any

component removed during

assembly or servicing is

replaced and fastened prior

to starting.

BEFORE LIGHTING:

1. Heater should be thoroughly

inspected before each use, and

at least annually. If re-lighting a

hot heater, always wait at least

5 minutes.

2. Inspect the hose assembly for

evidence of excessive abrasion,

cuts, or wear. Suspected areas

should be leak tested. If the

hose leaks, it must be replaced

prior to operation. Only use the

replacement hose assembly

 WARNING: 

FOR OUTDOOR USE ONLY

CARBON MONOXIDE HAZARD

This appliance can produce carbon monoxide  
which has no odor. Using it in an enclosed 
space can kill you. Never use this appliance 
in an enclosed space such as a camper, tent 
or home.

OPERATION

10

HAMPTONBAY.COM

 

Please contact 1-855-HD-HAMPTON for further assistance.

8 a.m. - 7 p.m.,ETS,Monday -Friday, 9 a.m.-6 p.m.,EST,

8 a.m. - 7 p.m.,ETS,Monday -Friday, 9 a.m.-6 p.m.,EST,

Saturday 1-855-HD-HAMPTON HAMPTONBAY.COM

Saturday 1-855-HD-HAMPTON HAMPTONBAY.COM

Summary of Contents for PH01-SS
















Reviews: