background image

8.

Finishing the Fan

Installation

STANDARD CEILING MOUNTING

Align the locking slots of the ceiling canopy 

1. 

with the two screws in the mounting plate. 

Push up to engage the slots and turn clock-

wise to lock in place. Immediately tighten 

the two mounting screws firmly.

Install  the  remaining  two  mounting 

2. 

screws  into  the  holes  in  the  canopy  and 

tighten firmly.

Install  the  decorative  canopy  ring  by 

3. 

aligning the ring’s slots with the screws in 

the  canopy.  Rotate  the  ring  clockwise  to 

lock in place.

You  may  now  proceed  to  attaching  the 

4. 

fan blades.

CLOSE-TO-CEILING MOUNTING

Carefully unhook the fan from the mount-

1. 

ing plate and align the locking slots of the 

ceiling canopy with the two screws in the 

mounting plate. Push up to engage the slots 

Attaching the

Fan Blades

NOTE: Your fan features revolutionary advance-

ments for quick and easy blade installation.

and turn clockwise to lock in place. Imme-

diately  tighten  the  two  mounting  screws 

firmly.

Install the remaining two mounting screws 

2. 

into  the  holes  in  the  canopy  and  tighten 

firmly.

Install the decorative canopy ring by align-

3. 

ing  the  ring’s  slots  with  the  screws  in  the 

canopy. Rotate the ring clockwise to lock in 

place.

You may now proceed to attaching the fan 

4. 

blades.

WHEN USING THE STANDARD BALL/DOWNROD 

MOUNTING, THE TAB IN THE RING AT THE BOT-

TOM OF THE MOUNTING PLATE MUST REST IN 

THE GROOVE OF THE HANGER BALL. FAILURE 

TO PROPERLY SEAT THE TAB IN THE GROOVE 

COULD CAUSE DAMAGE TO WIRING.

LOCKING  SLOTS  OF  CEILING  CANOPY  ARE 

PROVIDED  ONLY  AS  AN  AID  TO  MOUNTING. 

DO NOT LEAVE FAN ASSEMBLY UNATTENDED 

UNTIL  ALL  FOUR  CANOPY  SCREWS  ARE  EN-

GAGED AND FIRMLY TIGHTENED.

FAILURE  TO  PROPERLY  SEAT    THE  BLADES 

ON THE BLADE BRACKETS AND ENGAGE THE 

LOCKING  MECHANISMS  COULD  RESULT  IN 

THE FAN BLADES LOOSENING AND POSSIBLY 

FALLING.

Mounting Posts

Blade Bracket with

Key-Slot Holes

Blade with 

Figure 13a

Visually insect the top of the blade bracket 

4. 

to ensure that the locking mechanism is se-

curely in place.
Repeat for the remaining blades.

5. 

Mount  the  fan  blades  to  the  pre-installed 

1. 

blade brackets by aligning the three key-slot 

holes in the blade with the three posts on top 

of the blade bracket (Figure 13a).

Hold the blade with both hands close to the 

2. 

blade arm and press the blade down firmly. 

Ensure the key-slot holes are properly seated 

on the blade bracket posts.

While still holding the blade down with both 

3. 

hands, firmly slide the blade away from the 

motor  housing  until  the  blade  engages  in 

the locking mechanism. Make sure the steel 

locking mechanism at the rear of the blade 

bracket springs upward and butts against the 

edge of the blade indicating a secure connec-

tion (Figure 13b).

Summary of Contents for 52" Huntington III

















Reviews: