HAMOKI TP-16L Instruction Manual Download Page 5

6. 

Do not use old oil containing impurities, so as not to lower the boiling point. This will 
easily cause boiling or excessive soot. 

 

INSTALLATION PRECAUTIONS

 

Please do not install or store the device in the following locations to avoid malfunctions: 
 

1. 

Unstable table or counter. 

2. 

Where there are flammable and explosive items around. 

3. 

Places where the temperature is too high, the humidity is too high, and the dust is too 
much. 

4. 

Location where the power supply voltage is unstable. 

5. 

Where there is no good grounding device. 

6. 

Persons who are vulnerable, minors or have sensory impairments, should not be in 
direct contact with the device. 

7. 

To prevent environmental pollution, a smoking exhaust device should be installed in 
the place where the fryer is installed. 

 

PRECAUTIONS WHEN FAULT OR ABNORMAL 

CONDITIONS OCCUR

 

1. 

If the fault or abnormal situation occurs, please stop using the device, disconnect it 
from the power supply, contact a qualified technician to review the unit. 

2. 

Please do not use the pressure fryer when it is in an abnormal state. Do not 
disassemble, repair or perform maintenance as specified in the manual. Other 
maintenance and debugging should be carried out by certified professionals to avoid 
electric shock, severe injuries and greater malfunction. 

3. 

When the oil leak is found, cease using the device immediately, and have employ a 
qualified engineer to review and repair. 

 

OPERATIONAL PRECAUTIONS

 

1. 

The machine should be operated by the designated personnel to master the correct 
use of equipment. This manual does not apply to persons who are vulnerable, minors 
or have sensory impairments. 

2. 

The lid should be kept in place to ensure the pot is kept clean, and to preserve heat 
and pressure whilst in use. When adding the lid, please pay attention to ensuring there 
are no water droplets on the lid, that can drip into the hot oil, causing splashing and 
injuries. When the pot is in operation, it should not come into contact with untrained 
users and customers. The countertop and the outer casing of the pot will have a high 

Summary of Contents for TP-16L











Reviews: