Hameg HM8040-3 Manual Download Page 13

13

Subject to change without notice

Triple Power Supply

HM 8040-3

Deutsch....................................... 4

English ........................................ 13

Declaration of Conformity ......................................................

14

Triple Power Supply HM 8040-3 ............................................

15

Specifications ........................................................................

15

Important hints ......................................................................

16

Used symbols .......................................................................

16

Unpacking .............................................................................

16

Installation .............................................................................

16

Transport ..............................................................................

16

Storage .................................................................................

16

Safety instructions ................................................................

16

Correct operation ..................................................................

16

Warranty ...............................................................................

17

Maintenance .........................................................................

17

Overtemperature protection ..................................................

17

Designition of operating controls ...........................................

18

Basics of power supplies .......................................................

18

Linear regulators ...................................................................

18

Parallel and series operation ..................................................

18

Parallel operation ...................................................................

19

Current limiting ......................................................................

19

Electronic fuse ......................................................................

19

Concept of the HM 8040-3 ....................................................

19

Output power .......................................................................

19

Overtemperatur protection ....................................................

19

Switching the outputs on/off .................................................

19

Introduction to the operation of the HM 8040-3 .....................

20

Survey of controls and displays .............................................

20

Contents

Summary of Contents for HM8040-3























Reviews: