background image

24

Subject to change without notice

Control-Elements

 DISPLAY

 (7-segment LED + LED)

The digital display shows the measurement value 
with 4¾ digit resolution, in which the largest fi -
gure is used up to “5”. It will also display various 
warning messages. The measurement value will 
be displayed with decimal points and polarity sign. 
For DC measurement, a minus sign will appear 
in front of the fi gures when the positive polarity 
of the measured value is connected to the COM 
input 

.

    (LED)

Indicator denoting validation of the audible con-
tinuity  test  signal.  When  used  as  an  ohmmeter, 
the audible signal triggers when the measured 
resistance value is less than 0.1% of the range 
or 50 counts. For other functions, the indicator 
is hidden.

    BEEP

 (pushbutton)

Pushbutton for activating the audible signal.

 A  

(safety terminal for 4 mm banana plugs)

Connection (high potential) for DC and AC 
current measurements in the 10 A range in con-
junction with the COM input 

 (low potential). 

Current in excess of 10 A (max. 20 A) must 
not be applied for a period exceeding 30 
s, otherwise the internal measurement 
resistor thermal device will blow.

 mA  

 (safety terminal for 4 mm banana plugs)

Connection (high potential) for DC and AC current 
measurements up to 500 mA in conjunction with 
COM input 

 (low potential). The input is fuse-

protected. 

  HOLD

 (LED)

Indicator denoting that the displayed value has 
been frozen. The function can be activated using 
key 

. Deactivation is by pressing the HOLD/

OFFSET key.

 COM   

(safety terminal for 4 mm bana plugs)

The COM terminal (low potential) is the common 
connector for all the measurement functions to 
which the potential close to the ground of the 
measured quantity will be applied.

For safety reasons, the voltage across 
this terminal compared to the case (guard 
wire, ground) shall be 250 V at most.

  OFFSET 

(LED)

Indicator denoting that the displayed value is a 
relative measurement. The displayed value cor-
responds to the input value less the value present 

C o n t r o l - E l e m e n t s          

16 17

14 15

18

1

2 3

4

5

6

7

8

9 10

11 12

13

19

Summary of Contents for HM 8012















Reviews: