Hama 00050549, Operating Instructions Manual

Page: 6 / 58

4
5. Care and maintenance
Danger – risk of death from electric shock
Disconnect the mains plug from the socket before starting any cleaning work.
Warning - risk of cutting on the cutting rollers
Do not touch the cutting rollers.
Warning - damage to the device from moisture
Ensure, when cleaning, that no moisture penetrates the device in order to avoid
irreparable damage to it.
5.1 Emptying the container
Note
The status LED “Container full” on the “ ” button (9)
fl
ashes blue and the shredder
stops when the container is full.
•
Switch the device off - as described in 4.2 Switching the device off - and disconnect
the mains plug.
•
Pull the basket (5) out.
•
Empty the container.
•
Push the basket (5) back in.
•
Reconnect the device - as described in 3. Installation/Setup - to the power supply.
5.2 Cleaning the device
•
Switch the device off - as described in 4.2 Switching the device off - and disconnect
the mains plug.
•
Clean the device with a dry cloth. In cases of heavy soiling, the cloth can be dampened
a little.
•
Allow the device to dry completely afterwards.
•
Reconnect the device - as described in 3. Installation/Setup - to the power supply.
5.3 Cleaning / oiling the cutting rollers
Note
•
Oil the cutting rollers after each emptying of the waste paper basket in order to
prolong the shredder's service life.
•
You can fi nd an appropriate selection of cleaning products at
www.hama.com.
•
Switch the device on - as described in 4.1 Switching the device on .
5.3.1 Cleaning with Hama cleaners for shredders (item number: 113820)
•
Apply the Hama cleaner for shredders (item number: 113820) in several strips onto a
piece of DIN A4-size paper.
•
Insert the paper into the centre of the intake shaft (1). The cutting rollers switch on
automatically.
•
Once the cutting process is complete, the device is ready for operation again.
5.3.2 Cleaning with cleaning paper
•
Insert the cleaning paper into the centre of the intake shaft (1). The cutting rollers switch
on automatically.
•
Once the cutting process is complete, the device is ready for operation again.
6. Troubleshooting
Error Possible cause Remedy
The cutting rollers do not
switch on automatically
when material to be
shredded is inserted.
The “ ” button (9) was
not pressed.
Press the “ ” button
(9) until the status LED
“Ready” on the “ ”
button (9) lights up solid
blue.
The collecting container
(5) is not inserted
properly.
Insert the collecting
container (5) properly.
The connecting cable
(2) is not connected
correctly. Ensure that the mains
plug is in the mains
socket.
Error Possible cause Remedy
The cutting rollers do not
switch on automatically
when material to be
shredded is inserted.
The socket is not live. Check the domestic fuses.
The device is faulty. Notify Customer Services.
The status LED “Overload”
on the “ ” button (9)
fl
ashes red.
Too much paper has been
inserted or it has been
drawn in at an angle.
Follow the steps in
4.5 Forward/reverse
modes
and clear the
paper jam
The status LED
“Overheating” on the
“ ” button (9) lights up
solid red.
The device has become
too hot.
Switch the device off and
allow it to cool down for
at least 45 minutes.
The status LED “Container
full” on the “ ” button
(9)
fl ashes blue.
The collecting container
(5) is full.
Empty the container
(5) as described in
5.1 Emptying the
container
.
The cutting rollers
continue to run after the
shredding process has
been completed.
There is jammed paper in
the intake shaft (1).
Follow the steps as
described in
4.5
Forwards / backwards
modes
. Switch off the
device and check for
pieces of paper stuck in
the intake shaft (1).
7. Technical data
Input voltage 220 - 240 V~
Mains frequency 50 Hz
Max. power consumption 380 W
Dimensions (W x H x D) 35.0 x 51.9 x 24.6 cm
Weight (net) 10500 g
Weight (gross) 12200 g
Basket capacity for paper and plastic cards 20 litres
Max. noise level 62 dB
Max. cutting performance - paper (70 gsm) 11 sheets (DIN A4 paper)*
Max. cutting performance - paper (80 gsm) 10 sheets (DIN A4 paper)*
Max. cutting performance - plastic cards 1
Max. cutting speed 1.8 m/minute
Max. feed width for paper / plastic cards 220 mm
Cutting size for paper / plastic cards 2 x 12 mm
Max. constant operation time 15 minutes
Nominal rest period Min. 45 minutes
Protection class (as per DIN 66399) 3
Safety levels (as per DIN 66399) P-5 / T-5 / E-4
* Thicker paper, moisture or any voltage other than that permitted may reduce the
performance.
8. Warranty disclaimer
All of the technical information, data and instructions regarding operation contained in these
operating instructions was up to date at the time of printing and is provided based on previous
experience and to the best of our knowledge.
Hama GmbH & Co KG assumes no liability and provides no warranty for damage resulting
from improper installation/mounting, improper use of the product or from failure to observe
the operating instructions and/or safety notes.