Halton Safe Management 2.0 Installation, Commissioning, Operating, And Maintenance Manual Download Page 31

Page: 31 / 88

4. Set the type of an external control. For instructions, see

Setting the type of a unit

Value

Description

Alarm

The external control sends alarm indications.

Demand Close

The external control forces the alarm group (zone)
to close.

Demand Open

The external control forces the alarm group (zone)
to open.

5. Set the connector type of an external alarm device.

a. On the row of the external control, select the "Connector" column.

b. In the selection window, select a value, then select "Change".

Value

Description

Normally Open

Normally Open (NO) alarm device

Normally Closed

Normally Closed (NC) alarm device

6. Make sure the connector type of the external fire system connected to the Halton Safe Management 2.0

system is correct. Select the "Connector" column on the row of the external fire alarm, then do as instructed
in the previous step.

Halton Safe Management 2.0 (SM2) - Installation, commissioning, operating, and maintenance guide

1.0

Summary of Contents for Safe Management 2.0

















































































Search results

Summary of Contents for Safe Management 2.0

Reviews:

Brands by name

Popular brands

Halton Safe Management 2.0, Installation, Commissioning, Operating, And Maintenance Manual

Search results

Summary of Contents for Safe Management 2.0

Reviews:

Brands by name

Popular brands