background image

6

ECOVENT Operating Instructions

ECO

V/1

120

12/re

v1/EN

Section 1 – Installation

1.5 Commissioning

 

Information:   

1.5.1. Sequence of Operation. If all of the services have been

 

 

 

 

connected correctly, the sequence of operation is as follows.

 

 

 

 

Green illuminated on-off toggle switch will turn condensate hood

 

 

 

 

power on. At this time the fan will run at low speech (Idle). When

 

 

 

 

the door of the oven is opened, the magnetic reed switch triggers

 

 

 

 

the fan to increase in speed, and a cold water mist to be produced.

 

 

 

 

This will run for 24 seconds (factory setting) before returning to idle.

 

 

 

 

Closing the door will also return the condensate hood to idle.

 

Instruction:    

1.5.2. Prior to running the condensate hood for the first time, ensure

 

 

 

 

that both the mesh moisture eliminator (5) and baffle filters (6) are

 

 

 

 

fitted. Ensure all services and drains have been connected as

 

 

 

 

described in section 1.4 and oven is switched off.

 

 

 

 

1.5.3. Turn power on via toggle switch. Fan will run. Open oven

 

 

 

 

door to confirm activation of reed switch and allow to run for the

 

 

 

 

full 24 seconds. (Until the water stops automatically.) Open and

 

 

 

 

close the door twice more (and run for the full 24 seconds), to

 

 

 

 

allow the weir in the base of the condensate hood to fill. The

 

 

 

 

condensate hood is now ready for use.

Summary of Contents for ECOV-10











Reviews: