halstrup-walcher EMA 200 Instruction Manual Download Page 3

 

EMA 200 Instruction Manual 

1  Purpose of instruction manual 

 

This instruction manual describes the features of the EMA 200 digital pressure gauge 
and provides guidelines for its use. 
 
Improper use of this instrument or failure to follow these instructions may cause injury 
or equipment damage. All individuals responsible for operating this instrument must 
therefore be properly trained and aware of the hazards, and must carefully follow 
these operating instructions and the safety precautions detailed within. 

Contact the 

manufacturer if you do not understand any part of this instruction manual.

 

 
Handle this manual with care: 

  It must be readily available throughout the lifecycle of the instrument. 

  It must be provided to any individuals who assume responsibility for operating the 

instrument at a later date. 

  It must include any supplementary materials provided by the manufacturer. 

 
The manufacturer reserves the right to continue developing this instrument model 
without documenting such development in each individual case. The manufacturer 
will be happy to determine whether this manual is up-to-date. 
 

2  Conformity 

This instrument corresponds to the state of the art and meets all legal requirements 
set forth in EC directives as evidenced by the CE label. 
 
 
 

© 2006

 

 
The manufacturer owns the copyright to this instruction manual. This manual contains 
data, instructions and drawings pertaining to the features and usage of this 
instrument; copying this manual in part or in full or distributing it to third parties is 
prohibited.

 

 

Summary of Contents for EMA 200


















Reviews: