background image

6

3

1

2

4

50 cm

5 m

94°

left

right

left

right

WITH BACKGROUND

WITHOUT BACKGROUND

centre

Stay outside of the detection field to avoid disturbances.

Select the corresponding mounting side.

The sensor learns its environment and automatically determines the detection field(s). 

Both RED LEDs flash slowly and the 3 visible laser beams automatically light up during 30 seconds.

The sensor memorizes the 
floor as reference point 
and signals a fault when its 
orientation is changed.

No reference point, no signal.

TIP:

The right mounting side 
is recommended.

MOUNTING SIDE

Adjust the 

lateral position

 

of the detection field.

Adjust the 

tilt angle

 of the 

detection field with the hex key.

Lock the position

 of the mounting 

bracket to avoid malfunctioning in 

case of extreme vibrations.

Unlock the sensor and activate the visible laser beams 

in order to position the curtains parallell to the door.

POSITIONING

In  case  you  want  to  install  1 

LZR  on  each  side  of  the  PSD 

in  order  to  detect  persons 

standing on the door threshold, 

the distance between the inner 

curtains of the 2 sensors should 

be max. 20 cm.

The visible laser beams stay activated for 15 minutes or can be turned off by the same sequence.

The distances between the 

curtains depend on the 

mounting height and side. 

The visible laser beams indicate 

approximately the postion of 

curtain C1.

C1

CAT2 

Pl d

CAT2 

Pl d

Summary of Contents for BEA LZR-T305













Reviews: