background image

Page 11

As shown in Figure 4A, 4B and 4C, slide in both upper chim

-

4. 

ney and lower chimney, pay extra attention to sharp edges 

on the chimneys and minimize chimney movements to avoid 

scratches on the chimneys. You may use a screw driver to 

prevent them from sliding down as illustrated in Figure 4C. 

Make sure the screw driver can withstand the weight!

Install the Duct Set onto the body of the hood by using six 4mm x 16mm Phillips Head Tapping Screw.

 

5. 

Install Aluminum Duct Tube on the Duct Set and make sure all joints are secured and air tight.

Figure 5

Figure 4A

Figure 4C

Figure 4B

Slide both 

chimneys 

upward

Recirculating (Non-Vented) Kit: 

If Re-Circulating Kit is not purchased, skip this step. Place the air diverter 

inside support frame so that its 6” round hole faces downward and secure it with four 4mm x 8mm Phillips Head 

Tapping Screws.

Air Diverter 

(Optional)

Support Frames

Ceiling

Upper 

Chimney 

(has vent

-

ing holes)

Lower 

Chimney

4mm 

x

 

8mm Phil

-

lips Head 

Tapping 

Screws 

(Optional)

Duct Set

Duct Set

Aluminum 

Duct

Installation

 (Continued)

WARNING

Excessive Weight

Require three or more person to move and 

install this range hood. Spinal or other bodi-

ly injuries could occur if it is not followed.

Summary of Contents for SV198 Series

































Reviews: